I am trying to flash a new Firmware to my Ender 3 Pro.
I am using the ESP8266 as an ISP via AVRISP over Wifi.
I have a 10mF capacitor between the ground and reset of the ESP8266
I followed this thread: ESP8266 as ISP program for ATMega16
When uploading I get the following output on console:
C:\Users\Chry>"I:\3dPrints\Firmware Pack Source Folder\Windows Arduino\hardware\tools\avr/bin/avrdude" -C "I:\3dPrints\Firmware Pack Source Folder\Windows Arduino\hardware\tools\avr/etc/avrdude.conf"
-v -V -p atmega1284p -c arduino -P net:192.168.178.59:328 -b 115200 -D -U flash:w:C:\Users\Chry\AppData\Local\Temp\arduino_build_166520/TH3DUF_R2.ino.hex:i
avrdude: Version 6.3-20171130
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "I:\3dPrints\Firmware Pack Source Folder\Windows Arduino\hardware\tools\avr/etc/avrdude.conf"
Using Port : net:192.168.178.59:328
Using Programmer : arduino
Overriding Baud Rate : 115200
avrdude: ser_drain(): read error: Falscher Parameter.
avrdude: ser_drain(): read error: Falscher Parameter.
avrdude: ser_drain(): read error: Falscher Parameter.
AVR Part : ATmega1284P
Chip Erase delay : 55000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 10 128 0 no 4096 8 0 9000 9000 0xff 0xff
flash 65 10 256 0 yes 131072 256 512 4500 4500 0xff 0xff
lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
Programmer Type : Arduino
Description : Arduino
avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x14
avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x10
Hardware Version: 4744608
Firmware Version: 0.2
Topcard : STK502
Vtarget : 1.8 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us
avrdude: stk500_initialize(): (b) protocol error, expect=0x10, resp=0x01
avrdude: initialization failed, rc=-1
Double check connections and try again, or use -F to override
this check.
avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x10
avrdude done. Thank you.
I can't seem to get it to work. Does anyone have any ideas?
I tried programming it directly: I use the standard Arduino ISP sketch on my ESP8266 and try to upload that way. Directly connected the ESP8266 to my computer. I get sync-problems now: avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x61 The Board in the arduino IDE is set to Sanguino 1284p and the programmer is set to Arduino as ISP.
