Questions tagged [ws2812]

An RGB LED, when run in a strip, is individually addressable.

Filter by
Sorted by
Tagged with
0
votes
2answers
493 views

WS2812B LED Stripe going crazy with Arduino and External Power Supply

I have a simple connection here: A WS2812B 5m 300 leds strip 5V; A Power Supply MS-150-5 150W 5V; Arduino with a simple code to blink 10 first leds; TEST: If I connect my power supply to my LED ...
0
votes
0answers
29 views

Powering LED strip with Power bank (Arduino UNO)

First time ever working with Arduino UNO. I'm trying to power my RGB LED strip (addressable 5050+WS2812 RGB 5V IP20) via a Power bank (2x USB-A. One port's max 12 V DC - 1.2A, 9 V DC - 1.6A, 5.1 V DC ...
0
votes
0answers
12 views

Wich power supply should I get? ws2812b 5m [duplicate]

I have a ws2812b 5v 5m led strip and I don't know wich power supply should I get. How much ampers I must have.
0
votes
2answers
34 views

Problem with power supply ws2812b Arduino 5v vs 12v

I have an Arduino wired to ws2812b with 10 100uF capacitors and 2 1000ohm resistors(picture). When I'm plugging 5v power supply everything is working when I plug 9v battery everything is fine but when ...
1
vote
1answer
905 views

Do I have to wire up my WS2812 LED strip in “series”, if I want to address each LED individually?

Let's assume I want to make an asterisk (*) out of LED strips. I want to control each leg individually, while still being connected to only one GPIO pin. The layout I had in mind, looks like this: ...
-1
votes
1answer
145 views

Troubleshooting WS2812B LED strip

I am doing a project for my master thesis and I have 6 stripes of WS2812B LEDs each one containing 77 LEDs. I finished the design and now want to turn them on. I used an old power supply to power it, ...
0
votes
0answers
23 views

WS2812B not fully working with NodeMCUv2 [ESP8266]

I have a problem with my NodeMCU v2 board and my WS2812B led matrix with 256 (32x8) LEDs. The Board cannot be able to turn on the 191th led and stops working after the 190th without changing the ...
0
votes
0answers
19 views

How to run a Mega 2560 and 300 WS2812b battery?

I have 300 LEDs (WS2812b) which form an interactive tabletop of a coffee table. Everything is running on an Arduino Mega. For testing, I'm running all of those from a power outlet and it works really ...
0
votes
0answers
120 views

5xWS2812B in parallel works fine in ESPHome but not in C code?

Facing a weird issue, that is probably something pretty simple, but I've went through ESPHome's code on Github and can't figure out. I've wired up 5 WS2812B controllers on an ESP8266 (Wemos D1 R1), ...
0
votes
1answer
26 views

Translating WS2812-LED-Strip-IDs when cutting up a strip to multiple parallel ones

Lets say i have 1 meter of WS2812 Strip at 60 LEDs per meter. Now i cut the strip up in to 6 single strips but keep the wiring the same and lay them out in parallel. So it would look something like ...
0
votes
1answer
100 views

CHSV arguments with FastLED

I'm trying to use CHSV with FastLED library and as I understand hue, value and saturation in the CHSV type are of type uint8_t, or 1 byte. My problem is with using variables: CHSV led = (hue, sat, ...
0
votes
0answers
37 views

wemos ESP8266 fastled webmaster slave copies the master

I have been searching for a solution and attempting to make a solution where that a wemos running an existing project consisting of using a web server to control ws2812b lights, the basic code allows ...
-1
votes
1answer
52 views

WS2812 Matrix colour problem. Power?

I have 8 8x8 WS2812 Matrix LED boards connected together to make 2 16x16 matrices. I have them connected with Dupont wires. I also power the 2 16x16 with Dupont wires that are connected to a 5v 60Amp ...
0
votes
1answer
77 views

How can I make FastLED set every 2 LEDs to the same color?

I'm controlling an WS2812 LED strip in which every 2 leds is controlled together - they are setup as "eyes" in a prop. I'm looking to control hundreds of these, so in an effort to save RAM I'd like ...
0
votes
0answers
32 views

5th Led wont turn on (ws2812)

I'm trying to re-use a piece of example code I found here: https://howtomechatronics.com/tutorials/arduino/how-to-control-ws2812b-individually-addressable-leds-using-arduino/ And I only have 5 LEDs ...
-1
votes
2answers
225 views

Schematic with Atmega32U4 and WS2812 Led (Smiley Shape). Does it work? [closed]

I'm new here and I'm a newbie in electronics. Since 1 year I'm playing around with Arduino (different types) and now I want to build my own thing: a smiley with WS2812D-F5 RGB leds. But I'm not sure ...
0
votes
2answers
440 views

NodeMCU burned, did I something fundamental wrong?

I have a NodeMCU where I connected a LED strip (WS2812b, which operates at 5V). NodeMCU is powered via USB 5V. The used power adapter can supply 2.5A max. I don't have a separate power supply for ...
1
vote
1answer
403 views

Using 18650 batteries with a 3.7v to 5v boost converter [closed]

I'm looking to set up a 1-meter strip of WS2812B LEDs (60 LEDs) with an off-the-shelf RF LED controller with a remote. The LEDs want a 5V supply - I've tried running them off 3.7v but the colour ...
0
votes
1answer
279 views

WS2812B only works while I measure the voltage

I'm going crazy, there is clearly something I'm missing here. I have a NodeMCU V3.0 and a 5V LED strip WS2812B with 10 diodes. I tested this first with a 5V 0.3A power supply, only powering 3 diodes, ...
0
votes
0answers
34 views

How to make an animation with custom WS2812b?

I want to make a diy LED matrix with WS2812b (7x35). I have a difficulty to program the led animation. Is there some kind of program that has easy interface to custom the led display and generate the ...
0
votes
0answers
139 views

Running 5v and 12v strips together?

I want to run 5v and 12v strips and halos together, i read that with the 12v strips, give 12v to the strip but the data is always 5 volts, and tie the ground to the ground of the 5v controller? I use ...
2
votes
3answers
5k views

Control multiple WS2812B strips with different leds count

First of all, my English is not that good so sorry if I made any mistake. I'm using the WS2812FX, an awesome WS2812 effect library base on Adafruit NeoPixel library to make a small controller for the ...
0
votes
2answers
98 views

Methodology for designing/prototyping LED patterns

Several of my projects go through this time-consuming and tedious phase: design a LED pattern for a geometry of WS2812 LEDs implement it with e.g. FastLED write to Arduino and see results goto step 1 ...
0
votes
1answer
693 views

Problem with html code in ESP8266 WebServer

Here I have a small problem: I have an ESP8266, to which I have connected a matrix of LEDs to move text (the array of LEDs is made with the tape of LEDs addressable ws2812); when you turn on the ...
0
votes
0answers
150 views

How to connect an addressable (ws2811) led-strip with long cable to an adruino?

I set up a light show on my Arduino and it worked perfect when I tested it. I connected the the data line of my 1 meters (3.2ft) of addressable ws2811 ledstrip direct on the breadboard next to the ...
1
vote
2answers
1k views

How to control Neopixel LEDs in parallel?

Imagine a collection of LEDs (Neopixel or otherwise) labeled 2 through 12. There may be more than 11 LEDs, so repeat numberings are allowed. I want a simple way to control them from a single Arduino ...
4
votes
2answers
151 views

FastLed LED Strip Output Checksum

I am wondering if anyone has ever connected the output of their LED strip back to the Arduino to read and make sure the strip is functioning correctly, kinda like checksum functionality. I am using ...
5
votes
2answers
541 views

How to deal with unusual neopixel grid

I have built a custom installation in my home with 896 WS2812 LED driven by an ArduinoMega 2560 and powered by several rails just fine. However, the installation is arranged in a checkerboard-like ...
1
vote
1answer
2k views

LED strip problem… getting red when expecting white with lots of pixels. Fine with 1 pixel

I have an Arduino Uno. I bought this LED strip: https://www.amazon.com/gp/product/B019DYZNO6/ref=oh_aui_detailpage_o08_s02?ie=UTF8&psc=1 Starting initially using FastLED library. When I tried ...
0
votes
1answer
80 views

Not getting pure color while using the FastLED with WS2812b

I am working with the LED strip WS2812b and FastLED library, currently I have only 3 LEDs connected in such a way that the first 2 receive a color (say green) and the last one receives another one (...
0
votes
3answers
45 views

WS2812 HELP. Need name of Unkown component [closed]

https://i.imgur.com/u5SIvLo.png I need to know what the little "thing" that i marked in blue is and how it works. Thanks. picture taken here: https://www.sparkfun.com/products/13282