Questions tagged [voltage]

Voltage is the difference in electric potential between two points of an electric circuit, measured in Volts (V). Voltage can be constant (DC) or varying (AC).

15 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
1
vote
0answers
32 views

Low voltage security

I'm building a circuit with a GPS sensor and an esp32. My input voltage is designed to be 5V but I experienced some issues where people put lower charger in input (<4V). As a result my esp32 will ...
1
vote
0answers
64 views

Transistors to use for eight voltage sweeps from two PWM Arduino pins

On my Arduino Mega, there are two PWM pins open. There are eight analog voltage inputs to a datalogger. They are connected through a PCB, and I need test them with a DC voltage sweep. (There are many ...
1
vote
0answers
69 views

ADC pin shutting off on its own under certain condition

A0 pin not working when full PV system in use I am using the DFRobot Leonardo with Xbee R3. I am using the A0 pin to read a 0-5V voltage from my voltage sensor, which samples and steps down 130VDC ...
0
votes
2answers
31 views

Load Resistor Use for Voltage Sensing by Arduino

I connected a piezoelectric film to a Arduino Uno board via analog input. However, as I was getting very high voltage values (reaching 5 volts without much movement). Therefore, I added a 1 megaohm ...
0
votes
0answers
31 views

How to measure multiple voltages (Thermocoupes)

How would one measure many (20-100) small voltages in the 0-80mV range with an Arduino? I will need to amplify them and put them into the ADC. But i also need to switch between them. I want to ...
0
votes
0answers
34 views

Making a voltmeter for PV system over 60 VDC

I'm trying to make a voltmeter for my PV system that can range from 24 VC to 120 VDC. I'm aware of the fact that we have Arduino modules available that can work for 25 VDC system. However in my case ...
0
votes
1answer
153 views

Detect power interruption on NodeMCU

Im using a 5v 1A power supply and connected to VIN pin on the NodeMCU. I also use 18650 battery to keep NodeMCU running in case the power supply shuts off due to power interruption. I'm planning to ...
0
votes
0answers
110 views

HC-05 3.3 voltage regulation

HC-05 Bluetooth RX requires 3.3 v (TX has a regulator built in) I understand my uno and nano are 5v Ive connected a 3.3v Zennor in series with a led and resistor and with multimeter established the ...
0
votes
1answer
90 views

Have I fried the voltage input on my Arduino Nano?

I tried using my Arduino Nano in a circuit, switched on power to the circuit and heard a crack and smelt a bit of burning - something shorted. I have plugged my Arduino into my PC with a USB, the ...
0
votes
1answer
104 views

Arduino Micro not providing regulated power

I have an arduino micro that works fine off USB. I need to power it from an external 12V power supply. When I connect the 12V supply to the adjacent VIN and GND pins, the arduino will not power up. ...
0
votes
0answers
15 views

Attempted to disable autoreset - now the voltage regulator only outputs 4.0v

I followed the guide from the Arduino website, by placing a 10uF capacitor between GND and Reset. However, now the voltage regulator only provides 4v (Vin=13V). It correctly has 5V when being powered ...
-1
votes
1answer
199 views

Can I power a Wemos D1 R2 via the VIN and GND pins?

Can I power a Wemos D1 R2 via the VIN and GND pins? If so, at what voltage?
-1
votes
1answer
758 views

Understanding schematics: resistors attached to Attiny85 pins V-USB

I'm currently trying to create my own Attiny85 usb thumb(to mimic an joystick). I understand that I have to limit the voltage on the attiny's pins that are connected to the D+/- pins from the usb. In ...
-1
votes
1answer
92 views

Multiplying the voltage output

I'm working on a project where my arduino is receiving a voltage 0-5V, I need the output to be 10V always. Is there a way to do that?
-1
votes
1answer
47 views

AC Voltage Sensing using Arduino Uno

Is it possible to sense AC Voltage using analog input for Arduino Uno or can it only read DC? I mean I've tried connecting an AC voltage source to analog and I'm reading some numbers. However, I don'...