Questions tagged [tft]

A thin-film transistor (TFT) screen

30 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
1
vote
0answers
84 views

Bug read an image from SD card and draw it on TFT

I have developed a code to read an image stored on my SD Card and display it on a TFT. I can read the image from the SD Card successfully but I cannot draw it on the TFT. I dunno where is the bug. ...
1
vote
0answers
55 views

Esplora: Connecting a 2-Wire Speaker to Arduino Esplora

I am currently trying to make a simple game system with my Arduino Esplora, however I have noticed something. The Arduino Esplora has no pins for a 2-pin speaker that I get from a RadioShack store (...
1
vote
0answers
72 views

Looking for hardware - 3.5" TFT with capacitive touch

I'm looking for a 3.5" display (480x320) with a capacitive touch attached. Anyone have some experiences? I want to drive the display with 8bit. If there are existing libraries that would be highly ...
0
votes
0answers
18 views

Output of mlx90614 to mcufriend tft/lcd, not getting displayed

Newbie here !! Im trying to display the output of my MLX90614 sensor on mcufriend tft display (with arduino UNO). But unable to do so. I can only see the TFT being lit to white color, text -> "Target" ...
0
votes
0answers
38 views

Displaying Keypad Input on TFT Display

For a project of mine I have always wanted to build an electronic load and I am mostly done. However I have found myself stuck at one part that I thought would be simple but has thus only caused ...
0
votes
0answers
19 views

Arduino UTFT Touch align RIGHT with margin

I am using a TFT Touch screen on an Arduino Mega, with UTFT and UTouch libraries. When I use the code below, the text is aligning to right, all the way to the edge of the screen. Is it possible to ...
0
votes
0answers
31 views

How to interface DS Lite Touch Screen with Arduino

I recently tore down my old DS Lite which wasn't working. The screens and speakers were still functional, so I decided to mess around with it. I have a working DS touch screen and an Arduino Uno. How ...
0
votes
0answers
32 views

Adafruit 2.8 TFT LCD Touchscreen 4 wire pins - unclear instructions

Warning - Noob question I am trying to follow the instructions provided by the vendor https://learn.adafruit.com/2-8-tft-touch-shield/touchscreen-paint-example to no avail. Specifically: We ...
0
votes
0answers
48 views

Generate & Display QR using Nodemcu on TFT Display ST7789 240*240

I have NodeMCU & ST7789 TFT display. I want to generate QR Code of any dynamic input and display it on my TFT display. Not able to find any suitable reference. All Standard QR code libraries only ...
0
votes
0answers
38 views

Arduino TFT LCD Data Logger

Can I use Arduino TFT LCD Module ILI9341 as a data logger? It has an SD card slot at the back, I wonder if the data will be saved on the SD card? Thanks!
0
votes
0answers
36 views

Leonardo doesn't have enough memory to run a TFT and handle MIDI messages

So, I got a Leonardo because I plan to build a device to draw MIDI CC curves on a touchscreen TFT to be sent over MIDI to a DAW. I'm in the initial testing stage, and got a basic Paint application to ...
0
votes
1answer
107 views

Use JYETech 2.4 Inch LCD Display Screen Module with Arduino?

I have this JYETech 2.4 Inch LCD Display Screen Module that I would like to use for a project I have in mind, however, I'm not sure how to wire it up with my Arudino Mega. Here is the datasheet for ...
0
votes
0answers
167 views

TFT ST7735 Library - Can't Display Bitmap

Using a cheap Chinese ST7735 type 128x160 display with the TFT_ST7735 library (https://github.com/Bodmer/TFT_ST7735). I'm using an Arduino Mega 2560, hardware SPI. Example works perfectly, ...
0
votes
0answers
36 views

TouchScreen GUI Reference Guide Help

Recently I have gotten some Touchscreens to add to my projects and I am very excited to use them. However, I am not sure where I can find a guide to help me create my own GUI with the touchscreens. ...
0
votes
0answers
69 views

Why does my TFT keep turning white after moments?

Alright, seems there is something wrong I am doing that I don't understand. Before I start explaining, my question is different than this white screen question. First of all my TFT ST7735 is working ...
0
votes
0answers
58 views

Arduino 3.5" TFT Display going blank after sending data through I2C

I'm trying to use I2C to send and receive commands between an Arduino UNO R3 and an Arduino Mega R3, with a 3.5" TFT display connected to the Mega. I have verified that my display is fully functional ...
0
votes
0answers
44 views

problem with char array iteration and strcmp

New to Arduino and programming so forgive me if this is trivial but I've searched and can't find an answer... Goal: I want to convert decimal values to their equivalent fraction... eg: 0.125=1/8. I ...
0
votes
0answers
327 views

What am I missing? ST7735 TFT white screen

I followed this guy's guide with regards to wiring, etc., and all I seem to be getting is a white screen, as shown in these pictures. Is there an issue with the guy's guide, I'm missing or there is an ...
0
votes
0answers
40 views

Is there software to make an interactive GUI for my TFT touch screen shield?

I was wondering this, because realized it takes quite time consuming due to all the lines of code I have to write.
0
votes
1answer
364 views

Can a push button be used for TFT LCD screens?

I am trying to link my TFT LCD touch screen to a few push buttons. May I enquire why my code is not working? I'm trying to link the screen and the button so I'm trying to make the image display a ...
0
votes
0answers
142 views

Nextion controlling Neopixel

I am looking to control an addressable LED Strip (WS2812B) mode via a Nextion display. Below is a short version of my code. CODE ////////////////////////////// // LED LIGHT SHOW PRESETS // ////////...
0
votes
2answers
4k views

Nextion Dual State Button

I am having an issue with my Nextion display. I have uploaded the following code via Arduino IDE to my Arduino MEGA 2560. My Nextion Editor shows the button as ID:9 on page0 named floor. I am not ...
0
votes
1answer
393 views

Using TTGO TS 1.0 TFT display

I'm trying to use the TTGO TS 1.0 display with a demo app from a different source. The demo app wants the following to be configured: #define PIN_NUM_MISO 17 // SPI MISO #define PIN_NUM_MOSI 23 ...
0
votes
1answer
2k views

Wiring parallel TFT with ESP32

I have this Parallel LCD TFT. I want to connect it with an ESP32 (NodeMCU). I am using the TFT_eSPI library. In the TFT_eSPI documentation, it says that the connection should be as following: // The ...
0
votes
0answers
787 views

Programming 5 inch TFT Display + Arduino Mega with Touch Shield (w/SSD1963)

I am newbie on Arduino and TFT Screens. But I am a semi-professional on programming and I decided to develop a device that can be controlled by Arduino via capacitive touch screen (there will be 2 ...
0
votes
0answers
575 views

2.8" TFT display without D/C pin

I got a TFT display module from China. The TFT does not has D/C pin, how could I connect TFT to UNO or which library should I need to use?? Here is the pin name print on PCB: VCC TFT_CS SDI (SDA) ...
0
votes
0answers
441 views

white screen : 2.8" TFT LCD Screen Module: HY-280TFT

i have a problem with my new 2.8" TFT LCD Screen Module HY-280TFT.i connect it with an Arduino Uno board like this way: Connect HY-TFT280 to Arduino UNO LEDA -> 5V LEDK -> GND VCC -> 5V RD -> 3.3V ...
-1
votes
1answer
46 views

How to create and edit fonts for the Adafruit GFX library?

I noticed that the TomThumb.h font included in the Adafruit GFX library has characters that have different widths, which is a problem for me because I'm doing text processing that requires characters ...
-1
votes
1answer
122 views

Drawing bitmap on TFT

So, my .ino file is like this (do not worry about TftDisplay library, it totally works fine and myDrawPixel function just calls the adafruit drawPixel function): #include "TftDisplay.h" #include <...
-1
votes
1answer
190 views

Use a 2.8" TFT with my Leonardo

for 2.8" diagonal color touchscreen TFT: Readme states: "Works with any classic Arduino '328. Solder closed three jumpers to use the ICSP header for use with Leonardo or Mega" What should I solder? ...