Questions tagged [switch]

In electrical engineering, a switch is an electrical component that can break an electrical circuit, interrupting the current or diverting it from one conductor to another

Filter by
Sorted by
Tagged with
0
votes
2answers
44 views

LCD screen won't stop printing the same characters twice

I'm hoping that someone might be able to help me figure out how to prevent my LCD from giving me double digits (i.e. 55, 66, 77 - instead of 5,6,7); I have 2 functions that are printing, so I'm ...
1
vote
1answer
32 views

Control 4 digital outputs with one switch

I want to control 4 digital outputs (d0, d1, d2, d3) with one switch. When the Arduino starts, they should all be in state LOW. Now, after pressing the button once, d0 should get HIGH. Another push ...
0
votes
1answer
69 views

Sketch starts and keeps counting on external power supply but not usb

Thank you for the add, total newbie here (electronics and arduino) on his first project. Trying to make a counter for a hay baler with two HAL effect sensors, (pin 5 & 6) and outputting to an I2C ...
2
votes
1answer
83 views

Digital Input using a button doesn't work properly when using it to control a relay

I'm trying to control a relay both via Bluetooth and using a switch. The problem is that, when the LED is off, I can turn it on with the switch but then if I turn off the switch the relay will stay on....
0
votes
0answers
26 views

Made a light controller for the holidays

I am a new the world of Arduino. I found on YouTube, how to build a light controller (https://www.youtube.com/watch?v=WvG9c84ApFA&t=39s). I follow every step but it doesn't work. Here are some ...
0
votes
0answers
35 views

How can I make a fingerprint scanner to work as a toggle for a servo motor using Arduino Uno?

Arduino Fingerprint Project Help Please!! I am a beginner and using Arduino Uno, a fingerprint sensor and a servo motor to build a door lock (school science project). I followed many videos and ...
0
votes
0answers
327 views

Nested “switch” statements menu

I know that menus were discussed perhaps a thousand times here and everywhere. But using a ready solution is not something that I'm looking for because I know I won't learn the concept if I use them. ...
0
votes
1answer
91 views

Switch Statement stuck in loop

I am writing a code for a user to enter a 4 digit pin, then use this pin later to unlock a box. The loop is stuck between the "ready to unlock box" and "enter pin" it just keeps flipping between ...
0
votes
1answer
569 views

Arduino Uno Motor control using 2 Relays, 2 Limit switches and Bluetooth. Forward Reverse Stop

Modified existing project from this link: Problem : Trigger limit switch to stop DC motor I modified this code to control two relays which are wired to motor poles for Forward or Reverse movements ...
0
votes
1answer
159 views

How to control RC power switch with Arduino-/Adafruit-Board?

I want to control (switch on/off) a solenoid valve via an RC power switch and an Adafruit M0 Feather Bluefruit LE. The RC power switch is this one, and this is the Adafruit Board Pinout. My ...
0
votes
2answers
38 views

Cycling through switch states

I'm making a desk lamp out of 2x WS2811 strips (attached to the triple ports at top right of board below). The brightness of the strips is controlled by a potentiometer, and the colour by a switch. ...
1
vote
0answers
34 views

Turning on controller with button and turning off with a timeout

I am making a device controlled by an ESP 8266 and am wanting to save power by having it power down when not in use. The desired behavior is for a momentary button press or vibration sensor activation ...
-1
votes
1answer
86 views

Using an NPN transistor as a switch to turn on/off a DC Motor

I am trying to control a 3V DC motor (FA-130) with my Arduino Uno, and am trying to do that using an NPN transistor (2N3904) as a switch, as shown in this diagram. I used the Blink example and ...
2
votes
2answers
712 views

Problem using an array inside a switch statement

I am having a problem when using a switch statement to check for something inside an array. I am using an int as my switch, then I compare the character arrays using strstr. So it reads like this: ...
1
vote
0answers
221 views

Adding a kill switch for servos with states - blink without delay code

I have many LEDs and two servos connected to one Arduino Uno, and the servos are programmed to move randomly indefinitely. However, I would like to install a kill switch for the servos by reading a ...
0
votes
1answer
73 views

New to arduino, help wiring relay

I am new to arduino and need some help. I just baught light bars for my jeep and wiring harnesses with them, the harnesses come with buttons and I wanted to replace the button and have them controlled ...
4
votes
1answer
90 views

Can I use an AC signal to make an LED light up with arduino?

I want to use a 220VAC load as a signal and act as a switch to my arduino so Labview could interpret it as an LED ON state. I used a 4n33 octocoupler but it seems that the LED Simulation on labview ...
0
votes
1answer
108 views

Code runs, then doesn't run after I add some routine code

I am programming an ESP8266-01. I have this code which I am using to operate an on-off switch, which is being used as an override switch for when the relay is turned on and off over the internet: ...
0
votes
2answers
23 views

Encoder coupled with motor shaft.Encoder is giving larger redings than expected

I am a rookie and i dont have much experience on arduino. please help me. I intend to build a robot that will drive on a straight path even on nonuniform surfaces like the ones we see in agricultural ...
1
vote
1answer
52 views

My Code turns on my LED even when my switch is not pressed

I am trying to create a circuit that will turn my motor when I clap. When the first limit switch is low, and there is only one clap, a solenoid pin is supposed to be engaged (currently an LED), but ...
1
vote
2answers
214 views

LED on same Pin as Toggle Switch, not illuminating

I am trying to do something I think should be relatively simple. I would like to read an input from a toggle switch, and have a red 5mm LED indicate the state of the switch. Rather, however, than have ...
0
votes
0answers
35 views

How to measure multiple voltages (Thermocoupes)

How would one measure many (20-100) small voltages in the 0-80mV range with an Arduino? I will need to amplify them and put them into the ADC. But i also need to switch between them. I want to ...
1
vote
0answers
29 views

How can I get the count of pulses of two encoders on the serial monitor?

I have two encoders; I connected them to pin 2 and 3 and I want to count the pulses of them to make two DC motors to work until it reaches a specified number of pulses, than stop working. I have ...
4
votes
2answers
319 views

Why digital pin not reading ON from push button switches connected to 5V and pull-down 10K resistor?

Here's my circuit: And the code: //pins const int control1 = 2; const int control2 = 3; const int enable = 9; const int pinDirection = 4; const int pinOnOff = 5; const int pot = A0; //states ...
0
votes
1answer
90 views

Replace 6 pin on/off switch on Power Bank with 3pin or 2pin?

I'm looking to finish up my project in a box and i'm using a battery bank to power the Leonardo micro pro and other components. The bank has a little on/off which on it which has 6 pins underneath. ...
2
votes
1answer
153 views

Is this a good way to filter noise due to vibration in limit switch?

I have a circuit connected as follows my limit switches which are attached to my structure sometimes gets falsely triggered, so I wrote this code to address it. My motor is supposed to go down skip ...
0
votes
1answer
77 views

Replace mechanical switch with electrical switch or relay

I have a remote controller for a portable heater, and working on a small project to be able to control the fan on/off from an arduino with Bluetooh HM-10 module. I thought a solenoid might work by ...
0
votes
2answers
204 views

Using a toggle switch to run part of a sketch

First, I am a beginner for this. I just ordered my first book on coding Arduino and I'm working through some simple applications using a DS3231 (that has a temperature reading), LCD, MicroSD card ...
0
votes
3answers
125 views

Defining array in switch case

I’m completely new to arduino, so be polite. I’m trying to program my esp32 to drive neopixels as seven segment display. So I take a digit and pass it to switch case and in switch case I mention which ...
1
vote
1answer
43 views

LED and Switch Compolation Error Arduino 101

I'm getting an error on line 9 for some reason, (digitalWrite(Sender, HIGH);), and I just cant figure out why. My goal is to have two sets of flashing patterns, one for each switch state. I don't know ...
1
vote
0answers
248 views

How to recreate this basic ALPS switch board in Arduino?

I want to recreate this existing ALPS switch board (the board on the left) in Arduino, so I can control the switches (and 3 memory + 1 menu buttons) from my laptop. The ALPS switch board connects to a ...
-1
votes
1answer
58 views

Adding a switch to control log interval [closed]

HI this is a code for a set of logging scales. What I want to do is to add a switch that changes the logging from the set time of 1000 mills to either 5000 mills or 10000 mils depending on the switch ...
1
vote
4answers
374 views

How to boil down analog input to just three cases?

I am investigating the use of a 3-position-switch for one of my projects to switch between different settings using just one analog input pin. For the three positions I am using ground/0V, ~2.5V (via ...
-1
votes
2answers
118 views

Is there a key switch for Arduino? [closed]

I am trying to make a launch controller, which will turn on with a key. Like the one in this photo below:
0
votes
1answer
754 views

Arduino DC motor with 2 buttons

I have a problem with my Arduino project and I tried everything to fix it but nothing helps. I am trying to rotate my DC motor with two buttons: one button is to stop/start rotating on left side, ...
-1
votes
2answers
83 views

Button Switch arduino

I'm trying to use my button as a switch (the led goes on after I push the button and the led goes off when I push the button again). I know I have the right circuit, because I also used a code from ...
1
vote
2answers
980 views

Need Help in circuit diagram of 8*8 reed switch matrix

I am designing 8*8 reed switch matrix which will be connected to Arduino. I am using Arduino Duemilanove. I have completed the matrix portion but don't know how to connect and where to connect the ...
0
votes
1answer
306 views

TinkerCAD switch seems to be not working (always closed)

I am using TinkerCAD to simulate the functionality of a slide switch. Please comment if you think this question is off-topic. /* LiquidCrystal Library - Hello World Demonstrates the use a 16x2 ...
2
votes
2answers
355 views

Calculate sensor unique address with a 8 position DIP Switch

I have a large amount of sensor boards that I need to be able to configure setting unique addresses. Each sensor is attached to it's own arduino, I'm using a 8 position DIP switch for setting the ...
0
votes
3answers
328 views

Need help with a program for a button to change the display on an OLED display

So I am programming an OLED display from my Arduino Uno. I am trying to have a button that switches the different words on the display. (The words are just placeholders for programs as of now.) My ...
2
votes
1answer
88 views

How can I make a power button for my project powered by a USB powerbank? [closed]

I've solved the battery power supply issue for my Arduino project by simply connecting a USB powerbank. However, I just realised that I can't come up with a good way to add an on/off button! There ...
0
votes
1answer
344 views

Timer for Control Motor using Limit Switch

Im not good in arduino, but I have project that control motor using limit switch. The rule is: When switch OFF, motor ON When switch ON, motor OFF for 1 hour (i dont want use delay because cannot ...
1
vote
0answers
457 views

Difficulty connecting arduino ethernet with PC using a switch

Facing difficulty connecting arduino ethernet(w5100) with PC using a switch (Dlink). When both are connected directly(p2p) using ethernet cable, arduino device can be pinged. However, when connected ...
0
votes
1answer
83 views

Which transistor I should use to switch 12V 0.8A? [closed]

I am have circuit with Arduino NANO and I need to control air valve, which is powered with 12 Volts and 0.8 Amper. Problem is that Arduino NANO is powered with 5 volts. I want to use transistor to ...
0
votes
1answer
211 views

Transistor as switch for signal and high current buzzer [closed]

I'm a newbie in transistor switching. I have PIR sensors with C and NC onboard. NC is 12 V signal that I need to switch transistor (bipolar?) to emit 3.3 V (collector connected to 3.3 ...
0
votes
1answer
2k views

Problem : Trigger limit switch to stop DC motor

I want to make a project about automatic gate and garage door via Android app and connected by HC-05 bluetooth module. Each of the gate and garage door have two limit switches(located at each end of ...
0
votes
1answer
169 views

How to create “Auto switch case”

I am new to programming. I want to modify this sketch and I really need help. I have a switch case in this sketch, and what I want is an auto change effect. In this sketch 18 color effects for ...
0
votes
2answers
582 views

Can i use a range in a switchcase like in pascal?

in pascal's case statement i can use this: Var i : integer; ... Case i of 1..5 : DoSomething; end; i was wondering if there is a way in can do this with c/c++ in the arduino compiler using:...
0
votes
0answers
325 views

limit switch and external interrupt

The INT0 pin of a custom Arduino-like board based on Atmega16 is configured in INPUT_PULLUP mode and connected to a N.O contact of a limit switch, the other end of the switch is connected to GND. in ...
0
votes
1answer
47 views

Servo speed in a Toggle Code

I am new to Arduino and am trying to figure out servos. Right now I have a toggle button code for the servos. Although I want to know how to speed them up. Is there a way to do this? Currently, this ...