Questions tagged [sleep]

Sleep refers to a form of power management, where the processor can be instructed to enter various levels of "sleep". Use this tag for discussions about sleep mode.

22 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
3
votes
2answers
913 views

SIM800L and Arduino Sleep - getting whimsy Serial output after 5 calls

i'm working on project where i'm trying to achieve that arduino parse caller ID so i can use it later to send SMS with sensor reading data. Somehow i made that code (with much googling) and it works ...
2
votes
0answers
356 views

Is it possible to put ATtiny85 to sleep while using TinywireS?

I have an arduino uno as the master I2C device talking to an ATtiny85 as the slave. What I want to do is have the Attiny85 receive a message from the UNO to tell it to power off which will then ...
2
votes
1answer
1k views

PIR sensor and sleep (interrupt) on Mega2560

So I was starting to gain some knowledge on the PIR sensor and how to let the Arduino 'sleep' while there is no movement detected by the PIR. I found the following code somewhere and looked fairly ...
1
vote
0answers
50 views

How to wake up Arduino with an rtc?

I am doing a data logger with an Arduino Mega2560 and I want to use a code to make it sleep when no measure is needed and wake it up with an RTC when time comes. The reason I want this is because I ...
1
vote
1answer
157 views

Threshold to wake up signal

I have a sketch to put to sleep and wake up an Arduino Pro Mini 5V, but the problem is that sometimes when it is moved fast it wakes up itself, thing that I do not want. I have it configure to be ...
1
vote
0answers
238 views

Sleep mode Arduino Due through IR receiver control

I need to put my Arduino Due into sleep mode in order to consume less power. My Arduino Due receives IR data and does some work with it, but I need to make it sleep until there is no data. If data ...
1
vote
1answer
751 views

ATSAMD21 sleep + watchdog?

Has anyone got sleep/standby + watchdog to work together on their Arduino Zero or Sparkfun SAMD mini? I am able to get the WDT to reset the device, and am able to put it to sleep - but can't get the ...
0
votes
0answers
25 views

Possible race condition using ADXL345, external interrupts and sleep

Setup: I have an Adafruit ADXL345 attached to an Adafruit feather 32u4, via I2C lines and an interrupt line. Goal: The microcontroller should be in a sleep condition when acceleration values are ...
0
votes
0answers
82 views

ESP8266 spend 10mA, even though It is in the deep sleep mode

I am using Nodemcu ESP8266. I want to know how much my ESP board consume the battery during sleep mode. as the Mannual said it spend about micro-ampere, but my multi meter said it spend 10 mili-ampere,...
0
votes
0answers
34 views

How to get interrupt while in sleep mode?

I am using Arduino-uno, attached ESP-01 module I want to give interrupt when I send some wifi-signal to arduino, which is in sleep mode. so I write this code: SoftwareSerial esp(2, 3); // RX, TX ...
0
votes
0answers
48 views

STM32 (F103C8) could not wake up after sleep

#include <RTClock.h> #include <libmaple/pwr.h> #include <libmaple/scb.h> RTClock rtclock(RTCSEL_LSE); #define SCB_SCR_SLEEPDEEP 4 #define SCB_SCR_SLEEPONEXIT 2 #define ...
0
votes
0answers
67 views

Millis() does not back to zero after woke up from deep sleep mode

I am going to make a project that needs four boards of Arduino which synchronization in time is needed. The project is about capturing the timestamp (in ms resolution) whenever something is crossing ...
0
votes
0answers
52 views

Waking up a NodeMCU when force load is applied to device

I am currently designing a device that will take measurements from a load cell that is in tension. I am using a v1.0 NodeMCU device that features an HX711 load cell amplifier and is running off of ...
0
votes
0answers
23 views

Wemos D1 mini, will not restart after power fail

I have a Wemos D1 Mini on a solar-powered station outdoors. Every ten minutes, it wakes from deep sleep and sends the current temperature via mqtt publish. Works just fine. However in my ...
0
votes
0answers
63 views

ESP8266 http.get() issue due to wifi authentication failure

Facing a weird issue while reading data from esp8266. I am trying to read dynamic data from a demo text file on test server on same network in deep sleep mode. Case1: Joining new network I am using ...
0
votes
0answers
59 views

Using Sleep with Interrupts

I have 2 doors closet, that I want to lit when door is open. I use 2 prox sensors to detect state, an Arduino Pro mini, and 2 led strips. I use same code and hardware ( minus not needed doubled ...
0
votes
0answers
228 views

How can I put this display SSD1306 to sleep?

I have built a kitchen timer and it is supposed to spend most of its life in sleep mode in order to save power. I am using the SSD1306Ascii library (SPI) by William Greiman. In this library I have ...
0
votes
0answers
151 views

Is this a good way of making a low power attiny? Unpower instead of sleeping

I am making a low power rf remote that just has 3 buttons and sends rf signals accordingly. I've been trying to make pin interrupts work when it's in deep sleep but it's a huge hassle. And then I ...
0
votes
1answer
108 views

Switch controlled power saving esp8266

I'm trying to build a door sensor with the esp8266. I want it to be battery powered and use deepSleep for power saving. I'm going to use a normally closed reed switch between D0 (GPIO16) and RST. I ...
0
votes
0answers
527 views

Wake up arduino mini with a external signal from a rf wake up receiver

I am working in an arduino which sleeps after 1.2 seconds of running time and wake up when receiving a signal in the pin 2, but this last part is not working. I tried with the four modes of the ...
0
votes
1answer
121 views

How to use one button with interrupt to enable and disable sleep mode?

I have written a program for a kitchen timer. The timer uses just one single rotary encoder with a push button on its axis. It has modes for counting up and for counting down. After counting down it ...
-1
votes
1answer
324 views

SimpleAudioPlayer + sleep function

I have tested the SimpleAudioPlayer example. https://www.arduino.cc/en/Tutorial/SimpleAudioPlayer This works fine, but when I add a sleep(1000) at the end of the loop() function, the music sounds ...