Questions tagged [signal-processing]

Use this tag if your question is related to signal processing techniques (within the Arduino's capability).

17 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
1answer
63 views

How to separate a specific frequency signal from a summation of a few signals?

I want to calculate THD. SO how do I isolate the fundamental frequency from a signal with harmonics? I have a signal V which is a sum of V1, V2 and V3. V1=A1sin(w1t+phi1), V2=A2sin(w2t+phi2) and V3=...
2
votes
0answers
720 views

read with Arduino SSI encoder signal

I'm stuck in my project, I try to read an absolute encoders angular position with my Arduino. I used and cabled a differential line receiver and driver between Arduino and the encoder, like explained ...
2
votes
0answers
673 views

3 square wave pulse by 120° phase shift and 3 inverted of each by Arduino

I want to make a three phase inverter (DC to AC) bridge type using Arduino. For that I want to generate three square wave each is 120° phase shifted and other three waves of main three wave forms ...
1
vote
0answers
37 views

line following IR sensor not giving readings at 3m wire length?

I am using line following IR sensor with arduino mega. I need the sensor 2-3m away from arduino since the length of rover is 2m (sensor front & motor back). However, I cannot get accurate analog ...
1
vote
0answers
80 views

ultrasonic phased array

I have the following code for Arduino mega to output 40 kHz square waves at the analog pins. I need to apply specific phase delays for the signals at each pin though and am struggling to find out how ...
1
vote
0answers
41 views

Signal reading from existing snackmachine

So - i started a project at my civil-service. I want to fill a old snack-machine with things we need in the ambulance (bandages, cool-packs, etc.) In order to get the current amount of everything ...
1
vote
0answers
158 views

Decoding RF Signal

I have a motorized curtain and I'm trying to understand its rf control signal in order to control it from my arduino. I got the times, and checked the code is not static. I believe it has some kind ...
1
vote
0answers
403 views

Configuring Timers to Add One More 50kHz Square Wave

I am generating two 50kHz square waves, but I would like to generate three square waves. I have problems with generating the third square wave. Basically, I need to configure the timer bits so that I ...
1
vote
0answers
556 views

Arduino Square Wave Phase Shift by 270 degrees

I am using this code to generate a square wave with Arduino and shift it by 90 and 180 degrees. However, this code is not able to shift it to 270 degrees. Could you please suggest how may I modify the ...
1
vote
0answers
345 views

arduino + mpu6050 + nrf24l01 >>>>>>>>>>>>nrf24l01 + arduino ( Not running fluently)

this is my setup: I have an arduino uno + mpu-6050 + nrf24l01 all attached together and am transmitting data from that mpu-6050 to another arduino with an nrf24l01 attached to it. I got the arduinos ...
1
vote
0answers
480 views

Which components to built remapping keyboard via USB in + out (remapped)

I know that it's fairly easy to change the emulate keyboard and mouse by Arduino. But I'm quite specific about the goal I would like to achieve hence I would appreciate if you could advise me which ...
0
votes
0answers
22 views

Decode rf remote signals with ESP32 or node MCU?

I'm trying to decide my rf remote signals using ESP32 or node MCU. I have tried with Arduino and was successful but for some reason it is not working on either ESP32 or node MCU even using the same ...
0
votes
1answer
30 views

communication between two arduinos using ENC28J60?

How can i connect and send data between two arduinos using a ENC28J60 ethernet adapters on both of them. Is there any guides or example codes for me to take a look from or any library which i can use ...
0
votes
0answers
647 views

Reading TCD1304 linear CCD Sensor

I want to read the TCD1304 linear CCD sensor with an ESP32 and I'm facing some problems. As a first "warm-up" and to get familiar with this sensor I tried to generate the sensors input ...
0
votes
0answers
68 views

With what can I replace this for loop so my Arduino doesn't spit jibberish?

I have this: for (int i = 0; i < (DELAY_SIZE - 1); i++) { if (check_tag_in_char(delay_chars[i], BOOK_UPLOAD_END_TAG)) { tag_pos = 0; Serial.println("Uploaded"); ...
0
votes
1answer
86 views

Arduino FFT noobie question

How do you obtain the real and imaginary parts of a signal using FFT in arduino? I could not find a particular tutorial with code for this purpose in the internet.
0
votes
0answers
190 views

Best approaches to reading a high-count quadrature encoder?

I have a 24v servo motor coupled to a 2,000 segment optical encoder that runs on 5v. That's 2,000 "ticks" per revolution at it's base resolution. (Full quad reading allows 8,000 ticks per revolution, ...