Questions tagged [reset]
Use this tag for discussing resetting the processor.
110
questions
1
vote
2
answers
562
views
Arduino Reset via Software (every day)
Dear Stack Exchanger's,
I want to reset my Arduino and system in every 24h for preventing frozen software and also other connectivity stuffs.
I wrote a program which connects a digital pin to reset ...
2
votes
1
answer
190
views
How to difference hardware reset and software reset?
I have an arduino code with an SD card where I save some data. When I load a new code, The SD must update with the new data that I put in the code, but if I reset the Arduino by the reset button, I ...
0
votes
2
answers
122
views
Is there a way to make the RESET pin work in the inverse?
Is there a way for me to have this work the opposite way?
I have one cable with an alligator clip hooked up to the reset pin and another hooked up to ground.
When I clip them both together, the board ...
3
votes
0
answers
67
views
ESP8266 requires two resets to wake up from deep sleep [duplicate]
I'm working with the following circuit using a NodeMCU:
I have the solder jumper bridged between RST and BTN. In addition to what's in the schematic, pins 2, 3, and 4 of J1 are connected to the ...
0
votes
2
answers
71
views
Keep Alive for Arduino
Sometimes the arduino locks up for some reason. It would be nice to know why, but the problem is more general. I have found a hardware keep alive that resets the controller if it doesn't respond:
...
0
votes
1
answer
117
views
How to you initialize a reset on a sht30 digital thermometer?
I have a sht30 that will output correct temperature readings for about 5 min and then will drift off.
So I'm trying to hit the reset every few seconds to keep the readings accurate.
I am on a nano ...
0
votes
1
answer
40
views
Accessing funcition in object via `->` is crashing (resetting) Arduino
I have several classes that call each other running on an Arduino Mega. I am using the ArduinoSTL library to get the std library, most notably the std::vector.
The core problem is as follows: my ...
3
votes
2
answers
164
views
Arduino Nano randomly resetting
I am currently struggling with an intermittent problem with an Arduino project.
Background
I am using a LabVIEW program to control a few pieces of hardware. One of them is a NEMA 17 stepper motor that ...
1
vote
1
answer
128
views
Standalone ATmega328P stops responding when RX is connected
I have followed this demo and have set up a standalone ATmega328P being programmed from a Raspberry Pi via the SPI lines. I have also added a 16 MHz crystal with 22 pF capacitors, as well as I have ...
3
votes
1
answer
336
views
ESP8266 always resetting after 65 second of running
I have a simple code where ESP8266 is asking MySQL database about actual state of LED (whether 1 or 0) and when DB has 1 ESP8266 turns LED on... But my problem is after 65-66 seconds of server running ...
1
vote
0
answers
118
views
Use serial communication on Sparkfun SAMD21 mini board
I am working on an economic module to be able to use serial communication with the Sparkfun SAMD21 mini development card. And I have one, the DTR (of my CH340G) do I have to connect it to the reset of ...
1
vote
0
answers
165
views
Trigger ESP8266 reset pin on broken connection
I have an ESP8266 which I wish to place in deep sleep until a reed switch senses a door being opened. The ESP8266 is woken from deep sleep by briefly raising the RESET pin high.
In my original design, ...
5
votes
2
answers
879
views
Jumping to bootloader from application code in atmega328p
I'm trying to program an Arduino Uno (atmega328p) using only the serial Tx/Rx lines (no DTR, so no automatic reset). This is so I can upload code via WiFi/TCP using an ESP-01.
To achieve this, I need ...
0
votes
1
answer
184
views
Reset HC-05 from within Arduino sketch
I have an HC-05 Bluetooth module attached to an Arduino Mega; the module is paired with a Raspberry Pi and fed data via a python program; there's roughly one send and one receive per second of about ...
1
vote
1
answer
865
views
Using RST pin as external power switch
I have Arduino Nano with powered over USB. I have the request for external (physical) slide switch acting as power on/off for Arduino even if USB is always connected.
Looking at documentation and ...
2
votes
3
answers
159
views
Arduino Mega keep states after reprogramming
Based on:
https://forum.arduino.cc/index.php?topic=440978.0
And some previous experience with Arduinos. What I would like to accomplish here is that I have a 8 channel relay board with the relays in ...
3
votes
1
answer
2k
views
AsyncWebServer giving wdt reset
I am using 3 Esp32 modules. One being master and other two being nodes.
Nodes are connecting to the master's AP. Master is connected with GSM module to execute the web api.
Master esp is having a ...
-1
votes
1
answer
318
views
ESP8266-01 Resetting when DC motor runs
DC motor: 3-6v
Servo sg90: 3-7.2v
Esp 8266 01: 3.3v
I have 2 Arduino Uno both has their own ac-dc power adapter.
Lets say, 1st Arduino is Ard1 and 2nd is Ard2.
The Ard1 communicates to a web ...
1
vote
1
answer
338
views
ESP8266 reseted due to relay / AC plugged
My Wemos card is reseting for unknown reason. For example, the pump plugged on the relay works fine till 1am and then the pump stop. After a few research I figured out the ESP should reset because all ...
0
votes
2
answers
48
views
Resetting Arduino UNO code (newbie)
So today I started to learn Arduino uno. I have an LM35 temperature sensor and I got what I needed from it. Now it's just keep calculating till I plug it off.
I know there is a reset button. When I ...
1
vote
0
answers
130
views
Infinite loop if Serial.println() is not used
I'm trying to reset my program from software using the third method described here: Reset an Arduino Uno in code
The function is basically showing some data on an OLED display and afterwards should ...
1
vote
0
answers
263
views
Motor keeps spinning crazily after UNO board reset
I'm using a NEMA 17 stepper motor with A4988 motor driver and Arduino Uno board. I have used full microstepping (1/16th, so one revolution = 3200 steps).
I'm coming across this strange problem. ...
0
votes
1
answer
164
views
How can I clear the memory of my Arduino in this case?
I have made a code using involving HID control. But it seems that I messed up, but I can't upload a new sketch(nor edit the wrong code), because my Arduino is constantly doing things like Ctrl+Alt+...
-1
votes
1
answer
740
views
Why should I connect GND to RST to send data through Rx using USB-TTL?
I've found that when I use Arduino Nano connected with USB everything is working great, and when I tryed to use it with USB to TTL connector I've understood that I can only read data. I tryed to ...
1
vote
1
answer
2k
views
Nano 33 IoT rescue from the dead: No USB. No upload mode
First of all: my board used to work fine.
Now my Nano 33 IoT turns ON (green light) when connected to USB on Mac but:
doesn't enter in upload mode after pressing twice on board button.
doesn't shows ...
0
votes
1
answer
272
views
Deep Sleep Reset with Shock Sensor
I am trying to design a circuit that wakes my ESP8266 (Wemos D1 Mini) from deep sleep using a shock sensor. I can achieve this using the reset pin but I need
it to ignore further requests to reset to ...
0
votes
2
answers
73
views
nodemcu GPIO6 clock
is there a way that i can declare gpio6 (CLK) as an input without getting a wdt reset? I'm somewhat new to circuitry, but my boss wants to use it(GPIO6) to talk with external devices. I have more ...
0
votes
2
answers
122
views
Reset arduino nano after disabling tx/rx
I know, i am a bit dummy sometimes and i don't know why i actually did this but here it is. I have an arduino nano and i want it to use an external power via the the Vin port using a 12V external ...
2
votes
0
answers
924
views
How to enable auto reset in Arduino Leonardo?
I am trying to program an ATMega32u4 microcontroller through arduino IDE. I have added external oscillator(16Mhz) and capacitors and few other connections according to the Schematic. I had put a ...
1
vote
0
answers
189
views
Unable to upload to Arduino Uno From Raspberry Pi
I am trying to upload code to my Arduino Uno from my Raspberry Pi 3B+ and have been following this guide.
After following the instructions and trying to upload, I received this error message.
pi@...
1
vote
1
answer
1k
views
Firmware backup and restore
I need to have the firmware stored somewhere on the board in order to get back to it after flashing a new firmware.
Is there a way to store a backup of the firmware somewhere, and use a button to ...
0
votes
1
answer
855
views
Reset Button not working + Can't Upload code , What is wrong?
I was testing and debugging a code I wrote for a robot with 3 stepper motors on (Arduino Uno + CNCShield V3 + a4988 stepper drivers). I want to disable drivers at will. so I bypassed EN pin on 2 of ...
2
votes
2
answers
595
views
ESP12E Soft WDT reset stack trace leads to libraries
Im using ESP12E DevKit v2 (esp8266 wifi module) board for controlling relays and displaying DHT22 temp,humidity on web server.
It runs smoothly when the web client is closed but when i leave the ...
2
votes
0
answers
643
views
Cant get rid of Soft WDT reset using ESP8266
Im using ESP12E DevKit v2 (esp8266 wifi module) board for controlling relays and displaying DHT22 temp,humidity on web server. It runs smoothly but after while i always get a watchdog timer reset. (If ...
1
vote
2
answers
145
views
Store value in EEPROM to perform different actions on reset?
I want the same button to wake up (reset) and put it to sleep but this is hard if the button is tied directly to the rst pin. My thought was to read and store a value in EEPROM so tell the chip what ...
1
vote
2
answers
2k
views
AVR software reset without watchdog
I wrote a generic avr program wrapper which already use the watchdog timer to restart - and after the watchdog reset - recover the the bad situation.
After this recover process i have to restart the ...
0
votes
1
answer
2k
views
Nodemcu 1.0 and boot mode (1,6) after soft reset
I have a problem with a nodemcu 1.0 (lolin) board. Sometime a soft reset is performed from the watchdog and the board freezes in boot mode (1,6) (I have to manually reset the board to restart it).
I ...
1
vote
1
answer
83
views
Arduino Resetting in Automotive Application
I have a complicated problem with my Arduino circuit being reset/crashing, I will try to describe the best I can.
The Setup:
Basically I have a Arduino 328P circuit that is monitoring some ...
5
votes
2
answers
2k
views
Power on reset with arduino uno can never happen. Can this be fixed?
When an Arduino Uno is powered on, the USB chip's DTR output pin may (is, in fact) low for a while. This means that the capacitor C5 is connected from the 328p reset pin to ground. Thus, when power ...
2
votes
1
answer
865
views
Triggering a soft reset (Arduino Leonardo)
I want to trigger a soft reset on my Arduino Leonardo, and after some searching settled on using the watchdog timer, as it seemed to be the easiest and cleanest way to do it.
However, I don't think ...
0
votes
2
answers
2k
views
D1 mini does not resume operation as expected after deep sleep
I'm trying to get the D1 mini to return operation after ESP.deepsleep(). The code below compiles and gives the expected output for the first run. Five seconds after the announcement that that the ...
0
votes
2
answers
5k
views
Arduino Pro Micro bricked?
I have a Pro Micro board at which tried to upload a sketch with sparkfun's Pro Micro 3.3v processor selected.
After the upload completed successfully the board did not run again and is not even ...
2
votes
1
answer
9k
views
ESP8266 - Sending a software Reset Command
I have an ESP8266 running an Arduino code to control a dual relay device ( Up, Down, Off ), both from a physical switch and MQTT commands. After mounting the device in place I have no access in case ...
0
votes
3
answers
104
views
Is it possible to insert your own routine into the Reset procedure
I'm working with ATmega328 NANO boards, and I would like to know if it is possible to INSERT my own routine, to be included in the things done during reset, BEFORE any pre-C initialization is done, ...
2
votes
1
answer
79
views
Using external reset to trigger radio receipt
I am designing a low-power RF application using an ATTiny (Adafruit Trinket).
When the system receives a radio signal, it needs to read some sensors, and transmit with that data. Because I am short ...
1
vote
0
answers
109
views
Motor unexpectedly moving at reset
I'm playing with the standard L298N motor board and Arduino MKR 1000. However something strange happens: when I upload a new firmware and when I turn on the Arduino power supply (every time Arduino ...
1
vote
3
answers
3k
views
Using attachInterrupt() to make a reset button for my code?
I have used attachInterrupt() to reset my program to the beginning. It actually interrupts while running the 3 states as shown below inside of the if statement but when I press the actual button it ...
2
votes
1
answer
201
views
Arduino(s) not resetting on Serial connection lost / re-established - why?
it seems that I accidentally found a way to make my two Arduino nano clones run without resetting on serial connection close/reconnect. On one hand, this behavior is much closer to the desired ...
0
votes
0
answers
157
views
Loop being restarted before it finishes?
I have a Loop process that does various I/O and delay operations and also logs to the serial port so that we can review the activity.
We what I think is the loop being interrupted. Normally the ...
0
votes
2
answers
681
views
ATmega 2560 with Arduino bootloader running issue
I have designed a board based on an ATmega2560 chip and I burned the bootloader by following this tutorial.
Now I am able to load Blinky and other programs using an FTDI cable. But the issue I am ...