Questions tagged [isp]

In-system programming (ISP) refers to the ability of chips to be programmed while installed in the system.

14 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
0answers
395 views

Can't reprogram atmega328p chips using nano as ISP

Using nano clone as an ISP on a breadboard- as shown here - http://www.martyncurrey.com/arduino-nano-as-an-isp-programmer/ Previously, it worked great. However, recently, chips that I have ...
2
votes
0answers
241 views

Programming an AVR using ISP

I am trying to program an atmega with arduino sketch using ISP only (mac user). So I know how to burn a boot loader, and then to program the chip using the TX, RX. But I would like to program it ...
2
votes
1answer
764 views

Unable to upload sketch after bootloader has been flashed on Arduino Micro

I have created my own custom Arduino Micro, but I am experiencing problems when I attempt to upload an sketch via USB in Arduino IDE. Here is how I program the Arduino Micro: avrdude -c ...
1
vote
0answers
81 views

Can I upload with avrdude 2 hexes with 2 usbasp connected to computer, one hex with one usbasp ? If yes, how?

If I have connected 2 usbasps in the same time to ubuntu, can I upload 2 hexes one after the other(using avrdude) on each usbasp without disconnecting a usbasp ? If yes, how do I select each port for ...
1
vote
0answers
105 views

In-application programming for the Arduino Uno

I would like to know if it is possible to read from and write to the microcontroller's (Arduino Uno's ATmega328P) flash memory using a program or "bootloader" previously stored in the flash memory (or ...
1
vote
0answers
136 views

Reprogramming a specific slave from the master ATTiny 85 (connected to IDE)?

Given that every ATTiny connected already has a bootloader (micronucleus) installed, here's my theoretical chain: Computer > Master ATTiny (Connected via USB) > ATTiny Slave A > ATTiny Slave B Is it ...
1
vote
0answers
102 views

Can't program Atmega644p over ISP

I am using the Arbotix-M (Atmega644p). I am trying to program it using an ISP from Pololu. Until yesterday, everything seemed to be working okay and we were able to upload to it without problems. ...
0
votes
0answers
8 views

Batch programming AVR chips via ICSP with an esp8266

I had an interesting idea recently, but don't have all the knowledge needed to make it work. I know that several people have made Arduino programmers with an esp8266, allowing them to program the ...
0
votes
0answers
25 views

What would cause fuses to be writeable but bootloader not to be writeable?

I am trying to burn a bootloader onto an ATmega328P-AN using an Microcenter knock-off Arduino Uno R3 as my ISP for several days with no luck. The farthest I've gotten is writing and reading a few ...
0
votes
0answers
276 views

avrdude: initialization failed, rc=-1 on Windows but works on Linux

I am using a Deek-Robot USBTinyISP to talk to an ATMega32u4 using avrdude. When I plug the programmer into my Arch Linux box, it works immediately with no drama, but Windows refuses to talk to the ...
0
votes
1answer
95 views

Using Arduino as ISP and SoftwareSerial at the same time

I'm trying to use my Arduino Uno as an ISP to program an ATTiny85 and at the same time check my board by using the SoftwareSerial library to output the values I'm getting from my sensor. Is this ...
0
votes
0answers
333 views

Atmega328p ISP won't work

I have a grbl board that runs on an Atmega328p. On the board I have also provided the ability to control the stepper drivers through an external control step and dir signals. The schematics are shown ...
-1
votes
1answer
251 views

Atmega328P and Arduino Studio and Pololu AVR - not working

I have standalone ATMega328p and I'm using external 16MHz oscillator, I hooked up and I triple checked my connections for Pololu AVR programmer and I make sure that I select a proper programmer \ ...
-1
votes
1answer
2k views

Arduino Mega 2560 as ISP for ATTINY2313 / ATMEGA328P

I have posted this on the Arduino forum also, but I give it more chance if posted here also. I've been trying to use my Arduino Mega as an ISP for programming two different ATMEGA328P's and a ...