Questions tagged [genuino]

The name Genuino grew out of the split between Massimo and Gianluca (aided in part by Microsoft of course, and a trademark wrangle that went wrong). Each side wanted to appear to be more "genuine" than the other. That lead to the "Genuino" name (a genuine Arduino), and a version number war with the IDE.

Filter by
Sorted by
Tagged with
0
votes
0answers
26 views

How would i add PID control to this servo motor control program. potentiometer

I have installed an AutoPID library (by ryan downing version 1.0.3) to my arduino IDE, but im not sure which parts i will have remove to get the PID to control the servo angle. Thanks for the reply, ...
0
votes
0answers
24 views

Trying to get a servo motor to move to certain setpoints when a control potentiometer shows certain values

Here's my Code so far: void setup() { Serial.begin(9600); } void loop() { float a; float angle; int setpoint; a = analogRead(A1); angle = map(a, 0, 1023, 0, 180); if ( (angle>0) &...
0
votes
0answers
21 views

Arduino Genuino 101 An error occurred while uploading the sketch

I having a Original Arduino Genuino 101 (intel) While uploading basic blink sketch "An error occurred while uploading sketch". I am using PC with windows 10 OS and the Genuino 101 is at comm port 16. ...
-1
votes
1answer
45 views

Power external daughter board from Arduino only powered by USB?

Been searching for an answer, but I see lots of talk about it, but not clear answers. Can somebody clarify this? If I power the Arduino only via USB, can I put a small daughter board? and power it ...
4
votes
1answer
7k views

What is the difference between Arduino board and Genuino Board?

I've got an Arduino UNO REV3 SMD EDITION. In the Arduino Editor, I've selected Arduino/Genuino Uno. In a tutorial, I saw Hardware required : Arduino or Genuino Board What is the difference between ...
0
votes
0answers
882 views

Can't reset Arduino Pro Micro

I'm trying to reset an Arduino Pro Micro with a new code and it is not allowing me to. I'm using an empty sketch to upload to the pro micro but I get different error messages every time. I think the ...
1
vote
1answer
401 views

CurieBLE receive data without pairing [closed]

I read exist articles about it, but still not understand how to do that. I have a Genuino 101 and an EEG Headband (neuro interface). Need to get data from neuro device. With external HC-05 bluetooth ...
0
votes
1answer
2k views

Navigating menus using buttons on Arduino

I have made a very short version of my code. It has the basic problem I am facing. I explain my code and problem below. #include <Adafruit_RGBLCDShield.h> #include <utility/Adafruit_MCP23017....
1
vote
1answer
341 views

Blinking cursor on Arduino is inconsistent and misses inputs

I am trying to write a part of a program that prints time and allows the user to move a cursor across it. I have the following code, but there are a few issues with it. #include <...
1
vote
1answer
2k views

Moving cursor on LCD and changing highlighted value

I have the code shown below. The goal is to change the value of hours, minutes or seconds based on where the cursor is placed. #include <Adafruit_RGBLCDShield.h> #include <utility/...
1
vote
2answers
5k views

Convert serial value into hex using in Genuino zero

hello there my code is here. /* Simple Serial ECHO script : Written by ScottC 03/07/2012 */ /* Use a variable called byteRead to temporarily store the data coming from the computer */ byte ...
-1
votes
1answer
200 views

autoCalibrateAccelerometerOffset() Why does my Z values swing from 0 to 1g in static condition?

I tried to implement the autoCalibrateAccelerometerOffset() function, through the code below on Arduino Genuino 101. In a static test, without any stress or noise, I read the three axis value. ...
1
vote
2answers
2k views

How to use multiple SPI slaves in MKR1000 if it doesn't have Slave Select (SS/CS) pin?

I'm using a Genuino MKR1000 and I want to use the SPI interface, which I've seen that there is no Slave Select (SS)/Chip Select(CS) pin usage. How can I use the SPI interface with multiple slaves ...
1
vote
3answers
2k views

Genuino 101 - Can't upload my sketch - Timeout Error

I'm trying to run a sample sketch on my Genuino 101 but the following error shows up. Here is a verbose version. Starting download script... Args to shell: [/home/userk/.arduino15/packages/Intel/...