We’re rewarding the question askers & reputations are being recalculated! Read more.

Questions tagged [espressif]

Espressif Systems (688018) is a public multinational, fabless semiconductor company established in 2008, with headquarters in Shanghai and offices in Greater China, India and Europe. We have a passionate team of engineers and scientists from all over the world, focused on developing cutting-edge WiFi-and-Bluetooth, low-power IoT solutions. We have created the popular ESP8266 and ESP32 series of chips, modules and development boards.

Filter by
Sorted by
Tagged with
0
votes
0answers
40 views

esp32-cam reading bme280 with Arduino IDE

I am trying to interface BME280 with ESP32-CAM (Yes because later I need to take pictures also). Was following this tutorial. The BME280 board I have it has VCC, GND, SCL, SDA pins for hardware I2C. ...
0
votes
0answers
22 views

Lg g6 can't find Esp32 bluetooth

My lg g6 cant find esp32's bluetooth. Lg g6 bluetooth is fine as i can connect other devices Esp32's bluetooth is fine as i can connec from my samsung s9 to the esp32. Tried reseting and clearing ...
0
votes
0answers
46 views

Send HTTP request from Arduino UNO+ESP8266

I am trying to send an HTTP request from from an Arduino UNO through an ESP-01 connected by Serial. Communication with the ESP and connection to the AP work fine. But when i try to send an HTTP ...
0
votes
2answers
167 views

How to upgrade ESP8266 NodeMCU SDK from V2.5.2 to V3?

ESP.getFullVersion() output: SDK:2.2.1(cfd48f3)/Core:2.5.2=20502000/lwIP:STABLE-2_1_2_RELEASE/glue:1.1-7-g82abda3/BearSSL:a143020Connecting to DO_231455 I upload sketches from the Arduino IDE. How ...
1
vote
0answers
120 views

OTA updating the ESP32 from a separate server

I have an ESP32 project which I'd like to be able to update OTA. The trouble is that it is in deep sleep for approximately 15 minutes before waking up, connecting to WiFi sending an MQTT packet then ...
0
votes
0answers
40 views

Online Json Service for Esp32

I'm building a simple outdoor temp and humidity sensor with an esp32 I've aquired but I need a platform that I can submit the Json to so that then my laptop can make an http request to get the Json ...
0
votes
1answer
305 views

Stack smashing protect failure ESP32 with Modbus RTU

I'm doing a project using an ESP32 TTGO with LoRa, the Max485 and a WELLPRO ADAM 8082 for Modbus communication. I'm trying to use the ESP32 as a master to and the ADAM as a slave. I'm also using Node-...
0
votes
1answer
329 views

ESP32 bluetooth discovery parse names

I'm running a sample code from ESP32 examples and I'm scanning available BLE devices. I can see device MAC address etc. But for few devices I can't see their names.I am using ESP-WROOM-32 with ...
0
votes
1answer
38 views

A few questions on the first steps with an ESP32/ESP8266 NodeMCU [closed]

I would like to know what are the first steps, as a good practice, when receiving a new ESP based NodeMCU. For example: Checking if everything works fine After you connect to the relevant COM port, ...
1
vote
1answer
286 views

Adafruit esp32 Feather Failing to compile

So yesterday, I was able to upload/compile given example code to the Esp32 Huzzah board. Today I couldn't even compile. Even carefully using the tutorial adafruit provides. I was getting errors as ...
1
vote
1answer
779 views

Arduino Uno & ESP32 communication using RS485

I am trying to establish a communication between Arduino Uno ( Master) and ESP32 (Slave) using RS485 protocol (using MAX485 module). I have successfully done this between two Arduino Unos. ...
1
vote
0answers
77 views

Clock cycle count count for the same command is not equal in ESP32

I am using ESP32 Pico Kit with Arduino Ide. I want to measure operation cycle for a few commands. The code is so simple as below: void setup() { Serial.begin(9600); } void loop() { unsigned ...
1
vote
0answers
262 views

WindowsError(31, 'A device attached to the system is not functioning.') in arduino

Having board esp32 devkit v1, to get started with arduino ide (installed recommended boards for esp32) I marked board asDOIT ESP32 DEVKIT V1 (as no other options as like ESP32 DEVKIT V1 ) so upload ...
0
votes
2answers
184 views

How to / is it possible to change Vendor Name in ESP8266-12E?

I am aware of that it is possible to change hostname for ESP8266 but I want to change vendor name also so that it lists my company/product name in routers/firewalls. Is it possible?