Questions tagged [communication]

for questions about communication between multiple devices.

Filter by
Sorted by
Tagged with
2
votes
2answers
5k views

DFRobot GPS init error [Arduino Uno, SIM808]

i have problem with initialization DFRobot SIM808 actually when i try to recieve gps data by SoftwareSerial only it does works (i mean examples based on sending and reading command to and from serial'...
2
votes
1answer
1k views

How do I use I2C from an Arduino Uno when I have a GSM shield mounted?

This may be an extremely obvious question but I don't seem able to find a definitive answer. I have an Arduino Uno and a Sim900 GPRS/GSM shield fitted on top of it. I had I2C working on the Arduino ...
0
votes
2answers
36 views

Can RX pin(s) be used as TX instead?

Title question. I do not need any receive communication pins, only transmission. Actually, I need as many transmission pins as possible on any Arduino besides a Mega2560 (to re/write the EEPROM of ...
1
vote
0answers
14 views

SIM7000E WAVESHARE can't do anything

can someone help me im using sim7000e from waveshare one week ago its work normally at now its totally not work even can't read to RX-TX communication #include <SoftwareSerial.h> //koneksi ke ...
1
vote
1answer
24 views

Serial communication between nodemcu and Arduino Uno

For the last days, I am trying to establish serial communication between nodemcu and Arduino Uno but I failed to do this. Currently, I am working on a Home Automation project. I receive data from ...
1
vote
2answers
2k views

nRF24L01+ packet loss caused by Arduino reading and communicating with sensors

I have 2 Arduinos communicating with each other. My problem is that one sends packets every 1.5-2 seconds but the other Arduino does sensor reading and data uploading with a Wifi module, which may ...
0
votes
1answer
41 views

SD seems too slow for SMTP

I have asked this question on the arduino forum as well. I have used SMTP before using client.print (and client.println) but I am now trying to move as much text as I can from RAM to SD (and so I need ...
0
votes
1answer
122 views

Sending 4 analog values from one arduino to another with I2C

I have modded a cheap drone controller to output its joystick values to an Arduino Nano. I made it to output its 4 pot values using I2C to another Arduino don't ask why. So my problem is that I need ...
0
votes
0answers
32 views

Extremely bad analog read on ESP32 while using 433MHz module

I'm currently trying to transmit data from one ESP32 to another with 433MHz modules. I also need to read some sensor readings from an Hall sensor. When the ESP32 that sends is not connected the values ...
1
vote
0answers
19 views

Communicate/Configure with Pro Micro (using Joystick.h) from within Windows

I'm creating some Joystick-like controllers to augment simulator games. I usually use the Joystick library from MHieronimus which has worked great so far. Now, I'm using some non-momentary rocking ...
0
votes
1answer
913 views

How to communicate with GPS SIM900a without Serial Monitor

I am fairly new to Arduino. I was working on a project where I use a GSM SIM900a modem interfaced with an Arduino. The AT commands are sent via the Arduino to the GSM Modem. The problem, however, is ...
0
votes
2answers
3k views

Multichannel communication with Arduino and HC-12 transmitter

The HC-12 module has 100 possible channels starting at 433 MHz. Can someone tell me how to program the Arduino to use multiple channels at the same time? My goal is to build an RC transmitter with ...
2
votes
2answers
65 views

Arduino Yun receives UDP packets but prints them with gibberish

Arduino Yun is set to receive UDP packets. It receives those data with some gibberish. How is all set up: Arduino Yun (acts as a server) is connected through Ethernet to a PC which is (through WiFi) ...
0
votes
2answers
370 views

Share I2C pins with other device when lacking GPIOs

We're Using ESP12E as our MCU and we have three functionality : SIM800 connected to TX(GPIO1), RX(GPIO3) Matrix Keypad connected to GPIOs: 14,13,2,10,0,4,5,16 GLCD connected to GPIOs: 15,12 And we ...
1
vote
1answer
146 views

How to display CAN BUS information on EPS32 web server?

I try to display the transmitted information from CAN bus on ESP32 web server. I saved the CAN.read() in a buffer receivedChars[i] and try to display the data by client.println(receivedChars[i]);}. ...
2
votes
2answers
279 views

nRF24L01 - leaves out end characters during transmission

This is my Master's code. #include <nRF24L01.h> #include <RF24.h> #include <RF24_config.h> #include <SPI.h> RF24 radio(7, 8); const byte address[6] = "00001"; char text[20] =...
1
vote
0answers
28 views

Arduino serial issue

My arduino mega should be communicating with another card (ANET8) and also with a DC resistance meter (with python code) using 2 serial ports, one using the USB(resistance meter) and the other one ...
2
votes
2answers
180 views

Sending minimal data between two Arduinos far away from each other

Problem: I need to send small integer numbers (single-digit numbers suffices) between two arduinos located approximately 50-60m away from each other. The connection must be made through cables. I have ...
1
vote
1answer
46 views

Arduino Comms disrupted, prevents program loading (catch 22)

I have written some software which, when loaded onto an Arduino Micro, blocks communications for some reason. Lets stipulate that there is something wrong with it. Using the Ardiono IDE on Windows 10,...
4
votes
0answers
64 views

What’s the most stable digital communication protocol for sewable electronics?

I’ve spent the past few days trying researching communication protocols and I have a few issues. With sewable electronics, you need to work with cables with a fairly high resistance that are ...
2
votes
1answer
45 views

Communicate from Arudino to computer over 3.5mm port

I'm wondering if it would be somehow possibly to have easy communication with a computer for Arduinos that don't have USB like the pro mini. That would make an easy way of having two-way communication ...
2
votes
1answer
42 views

RS-485 Serial communication problem with arduino

I use 485 modules to transmit data serially from one arduino uno to another uno. If I connect the 2 arduino boards directly without using the rs485 module, the data is sent and received without a ...
0
votes
2answers
140 views

Communication between 2 arduino boards

I am not really 100% too sure how to do this but I am trying to make my arduino UNO communicate with my arduino MEGA. The reason why I needed to do this was because I was using the RFID module along ...
0
votes
0answers
20 views

Make Arduino Nano 33 IOT talk to another Arduino via Bluetooth

I have an Arduino Nano 33 IOT and I want it to talk to another Arduino that has an HC-05 Bluetooth module. Is this possible? I cannot find anything on the internet that talks about doing this.
0
votes
1answer
156 views

Flow control between ESP32 and RS323 device

I'm trying to communicate an RS232 device with an ESP32 (Heltec Wifi/LoRa 32 v2) my problem is that I don't receive any response from the device, doing some research, I'm thinking that the trouble can ...
1
vote
0answers
25 views

Communication b/w Arduinos, master(M) and slave(S) via Tx Rx pins. M sends query to S which shows the data in serialmonitor. S fails to send data to M

Slave code int arr[10] = {0,1,2,11,4,5,6,7,8,9}; char id = '1'; char re[2]; void setup() { // Begin the Serial at 9600 Baud Serial.begin(9600); } int ia; void loop() { Serial.readBytes(re,2);// slave ...
2
votes
2answers
12k views

Arduino master/slave communication using RS485

I am using Arduino Uno as a Master Device and 3 Arduino Unos as slave devices. I am sending data from each slave to master after every 3 seconds continuously, and is going to execute further logic ...
0
votes
1answer
32 views

I want to make two arduino to communicate over different wifi. Is that possible?

I want to make any 2 Arduino module from different places to communicate over wifi. I really need to know if it possible? If yes, advice me more about it. I want send data from sensor module from one ...
1
vote
2answers
84 views

Read Internal Registers of RS485

I am trying to interface sele EM2M, I am using Arduino Mega with RS 485 module. I want to read the internal registers I am using ModbusMaster library. The data which I want to receive is in the ...
3
votes
3answers
124 views

Using several Arduinos simultaneously

I'm working on a project where I need to control the light of 5 buttons as well as listen when each button is switched on/off by the user. I would furthermore like to provide feedback on an OLED ...
1
vote
0answers
29 views

Arduino communication

I want to message and call arduino board. I want some type of automation. But where should I get started I don't know I've tried sim900a module which was disappointing experience for me. Then I found ...
0
votes
1answer
75 views

HID communication between Arduino Uno and computer

I used some firmware I found online to turn the UNO into an emulated HID device. The Arduino is no longer connected to a Serial COM port so I can't send serial data from my computer to the device. Is ...
1
vote
1answer
35 views

Transmitting multiple values to the arduino, and Interpreting them with minimum delay

I am building an underwater robot, which can move Up/Down, Forward/Reverse, controlled by a Joystick. The situation is like this : USB Joystick is connected to a PC, PC is connected to an Arduino via ...
0
votes
2answers
31 views

Can I use The mpu6050 with this?

I am making a project with 3 arduinos (2 slave, 1 master) and I want to know can I use the mpu6050 since it uses the I2c communication.
1
vote
0answers
31 views

Send message to multiple number

sim.println("AT+CMGS=\"+91xxxxxxxxxx\"\r"); I don't want to write this. I want to write mobile number on serial monitor in Arduino and on that number, i want to send message. how ...
0
votes
0answers
23 views

Arduino Due SerialUSB Resetting

Having this basic example for using the SerialUSB function on the Arduino Due under Windows: // ARDUINO DUE BLINK LED void setup(){ pinMode(13,OUTPUT); SerialUSB.begin(2000000); while(!SerialUSB)...
1
vote
1answer
96 views

How can I display text on OLED?

I'm trying to print the information, which is received from the other ESP32 by CAN transceiver, on an OLED. The CAN bus is working perfectly, as the 'HELLO WORLD' is already be received. But I can't ...
2
votes
1answer
37 views

Simple ModBus Master function 15

I have a simple setup with arduino Nano as slave and a arduino Mega as master Can anyone explain how the function 15 FORCE_MULTIPLE_COILS Works i have been running some test on this and cant figure ...
0
votes
2answers
2k views

Arduino reads hc-05 device connecting status

Hello I want to get an arduino get status of bluetooth hc 05 if connect with device or not . I'm trying by myself and search on internet website but I can't find useful things.
1
vote
1answer
40 views

My two slave SPI setup on arduino not working correctly

I am trying to connect a DPS310 and an ADXL345 to my Arduino using 4 wire SPI. When the individually tested (i.e. each has its own script), the output is correct, however when the scripts are combined ...
1
vote
0answers
10 views

which kind of data are store If i terminate the call in sim800?

I'm working in SIM800 for DTMF based project. I want to know which kind of data are stored in the buffer during termination of call in SIM800. How to find if call was disconnected in SIM800? Also ...
1
vote
0answers
42 views

How could I combine sensor data with custom protocol und send it with Serial?

I am very new to Arduino. Now I am trying to send the sensor data to Computer. The sensor data will be stored as bytes into arrays. To build a robust transmission I'll pack the data with own defined ...
1
vote
0answers
92 views

Change arduino output from input

I'm trying to change values such that the arduino uno outputs comes from what is input, with the code, int PinOutput = 11; int PinInput = A0; int inph; int inpl; int input; void setup() { // put ...
0
votes
1answer
25 views

parallel communication simulation problem

Hi I am trying to send data(1 byte) from one arduino to another using parallel communication(a bus of 8 connections) and not using any library. However, the problem is the data gets corrupt all the ...
2
votes
1answer
604 views

ADS1262 and 2.2 SPI TFT (Two SPI Slave) with Arduino

I am interfacing two SPI slave module i.e. ADS1262 and 2.2 SPI TFT with the Arduino Ethernet board. When I test each device on its own it works. Initially, I interfaced the TFT to the Arduino and it ...
0
votes
2answers
117 views

Can I program the Arduino without having an actual board with the able to emulate a COM connection to the computer?

I have ordered my Arduino, but it is not going to arrive until 2 months, and I would like to be able to emulate a COM connection to the emulated Arduino. I am writing a program that listens on the com ...
1
vote
1answer
149 views

Using HC-08 bluetooth module with arduino

I have an arduino mega 2560 and a recently purchased HC-08 module and the connection is as the following: Arduino | HC-08 VCC - VCC GND - GND 14TX3 - TXD 15TX3 - RXD When I power up the arduino it ...
1
vote
2answers
898 views

Making two Arduinos/MKR1000 communicate

I am trying to create a project in my free time just for a bit of fun - it consists of two MKR1000 (one acting as a web server connected to one laptop, and the other acting as a web client connected ...
0
votes
3answers
76 views

What's the most direct way to assign Serial.read() bytes to an array?

I'm trying to send NMEA 0183 sentences through LoRa. Every dinstict NMEA message looks like several char arrays (sentences) followed by '\n'. In the below picture we see one NMEA distinct message: ...
-1
votes
1answer
83 views

Sending data struct with 2 int fields from Arduino to Raspberry via NRF24L01

I'm trying to do wireless thermometer on max31865 arduino and nrf24l01 but I'm having problem sending whole data struct I can send int or char arrays but when I try to send whole struct I got output ...

1
2 3 4 5
8