Questions tagged [avrdude]

Programming utility for AVR micro-controllers.

Filter by
Sorted by
Tagged with
0
votes
1answer
443 views

Getting a long avrdude error while uploading a simple sketch to arduino uno

This is the error which shows up after the sketch is compiled and starts uploading. Is there some sort of fix to this problem? There are no shields connected to it, not even I/O pins are being used, ...
0
votes
1answer
162 views

Arduino not responding [duplicate]

I have been using my arduino uno for many months and it worked very well even till today morning but an hour ago I tried to upload a sketch and arduino IDE showed my this "avrdude: stk500_getsysc(): ...
2
votes
0answers
259 views

Eclipse AVR for arduino not uploading

I recently read this post about setting up Eclipse for Arduino. I Build the test project with no erros, but when I go to upload my test project it just hangs at 5%, with no error messages. If I ...
1
vote
1answer
776 views

ArbotiX-M Problem uploading to the board

I have an ArbotiX-m Arduino board, and have followed the setup guide on Trossen robotics all the way to the 5th step. I have a Mac running OS X 10.10 and use Arduino 1.0.5. I installed the necessary ...
5
votes
1answer
7k views

Does ATMega 328/2560 chips support JTAG-type programmer and hardware debugger?

As stated in www.Arduino.cc FAQ, "Can I use an Arduino board without the Arduino software? Sure. It's just an AVR development board, you can use straight AVR C or C++ (with avr-gcc and avrdude or AVR ...
1
vote
1answer
2k views

How to upload an arduino sketch from java / processing?

I'm trying to upload a hex file from Java/Processing but running into some issues. Here is my code so far, based on the Arduino IDE's upload verbose output: void setup(){ //C:\Program Files (x86)\...
12
votes
3answers
51k views

When using Arduino Uno as ISP does “Yikes! Invalid device signature” mean a bad connection, bad config, or bad version of avrdude?

I'm using an Arduino UNO to program a pre-compiled hex image to an ATTINY45, using the avrdude in the Arduino IDE directory, on Windows 7. The Uno has the ISP sketch loaded from the examples directory ...
2
votes
1answer
7k views

How to modify Arduino boards.txt to support new MCUs

In this post, it was mentioned that to get the Arduino IDE to support an ATmega328 (only the ATmega328P is supported): I should mention the Arduino way of doing this, is to create a new boards....
-1
votes
1answer
917 views

Error uploading on Arduino Mega 2560

I'm completely new to Arduino, I bought a Rampos 1.4 and an Arduino Mega 2560 to build a Prusa Mendel 3D printer. But when I connect the Arduino via USB to my computer, open the software and click to ...
1
vote
2answers
3k views

Problem loading sketch to Leonardo

Today I got Arduino Leonardo to replace my Uno. I've tried running one of sketches I use on the Uno, but with no luck. When I start the upload, RX LED on the Leonardo flashes few times, and after ...
9
votes
4answers
56k views

Arduino compatible's serial port not showing Mac OSX

I bought an Arduino-compatible Freaduino board atmega8 (I selected the board type as Arduino ng or older atmega8). I installed the Arduino IDE on Mac OS X and the FTDI drivers. But my serial port ...
1
vote
5answers
3k views

Mega 2560 Doesn't Respond

When trying to upload to my Mega r2, it simply times out during uploading. avrdude: stk500v2_ReceiveMessage(): timeout avrdude: stk500v2_getsync(): timeout communicating with programmer I tried ...
3
votes
1answer
707 views

How to add the -F switch for avrdude in Arduino IDE

So, before starting to learn with something else, I'll give it one last try. The avrdude is complaining that the device signature doesn't match. Whatever, I don't care. To me, what's written on it is ...
3
votes
1answer
3k views

Reset fuses on atmega328p using Arduino

I bought a few atmega328p chips but unfortunately they came with the Arduino bootloader and they are set to use the external clock. I want to reset their fuses using avrdude so I can use the internal ...
1
vote
1answer
3k views

arduino 16u2 stk500v2_command(): command failed

I'm trying to fix arduino uno r3 that was burned-out. I changed m16u2 chip on it. and now I need burn in: Arduino-COMBINED-dfu-usbserial-atmega16u2-Uno-Rev3.hex I'm using stk500v2 and connecting it ...
10
votes
1answer
1k views

Understanding the compilation/linking/upload process (so I don't have to use the IDE)

I have started to play with and arduino UNO quite recently (without any prior experience with micro-controllers). I would like to use emacs instead of the IDE, and I'd also like to know what the IDE ...
6
votes
1answer
8k views

Change Options for the AVR Programmer via Arduino IDE

I want to program an ATtiny through the Arduino IDE. I have a somehow strange programmer. But I can upload via avrdude by avrdude -p attiny13 -P /dev/cu.usbmodemfa131 -c stk500v2 -F -B20 -U ...
4
votes
3answers
2k views

Can I corrupt my Arduino if it's unplugged during an upload?

When messing around with code and uploading a sketch to my Arduino board, I almost accidentally pulled out the USB cord. Everything is fine, but then I started thinking what would've happened if I had ...
10
votes
3answers
23k views

Arduino Mega timeout communication with programmer error

I have an Arduino Mega 2560 and it was working fine until about lunch time when I started getting this error: avrdude: stk500v2_ReceiveMessage(): timeout avrdude: stk500v2_getsync(): timeout ...
116
votes
20answers
238k views

“avrdude: stk500_getsync(): not in sync: resp=0x00,” aka Some Dude Named Avr Won't Let Me Upload My Program

I made an awesome program the other day, and I wanted to upload it to my Arduino. After clicking the upload button, some mean dude named avr came along and stopped me, saying: avrdude: ...

1 2 3
4