Questions tagged [atmega32u4]

atmega32u4 is low-power Atmel 8-bit AVR RISC-based microcontroller

14 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
0answers
158 views

Atmega 32U4 doesn't show on device manager after fuse bits reset

I am finally ready to try setting fuse bits on my ATMega32u4-AU custom board (8Mhz Ceramic Resonators, 3.3V), however, after I set the fuse bits and plug my board to computer, the device manager ...
2
votes
0answers
274 views

Bitmap only displays correctly with PROGMEM keyword

I have a bitmap to draw defined as below. PROGMEM const unsigned char ship1 [] = {0x18, 0x3C, 0x7E, 0xFF, 0x81, 0xC3}; It is then used by the arduboy library's draw slow bitmap function like so: ...
1
vote
0answers
230 views

It is possible to revive my Arduino Leonardo (mini beetle) board?

I have this board: It has the atmega32u4 chip. I have updated its code several times, and used it without issues for several months. Today, while updating (using Arduino IDE) it started to throw ...
1
vote
0answers
448 views

How to enable auto reset in Arduino Leonardo?

I am trying to program an ATMega32u4 microcontroller through arduino IDE. I have added external oscillator(16Mhz) and capacitors and few other connections according to the Schematic. I had put a ...
1
vote
0answers
55 views

Question about controlling servos with PWM while being able to accurately read the current from a sensor

Hi I am hoping to design a custom board ATMEGA32u4 with practically a Arduino leonardo bootloader. I plan to control up to 12 servos while being able to read back the current sensor voltage of an ...
1
vote
0answers
47 views

Get data from a running exe on my pc

I have made a button with an LED using an arduino micro. It's connected to my pc and when I hit the button, the LED activates and a recording on Reaper (digital audio workstation) is started. When I ...
0
votes
1answer
16 views

Wiring Multiple MPU 6050 to Micro/Lenardo

disclaimer I am new at hardware/circuits I am currently trying to connect two MPU-6050 to a single Micro board. In addition, there are 5 additional buttons to be connected. I am under the impression ...
0
votes
0answers
25 views

LUFA with pro micro 3.3v 8mhz not working

I am trying to flash my pro micro 3.3v from sparkfun with a Lufa project to make it act as a pokken controller, i am using this project Github Project I have modified the makefile for 8mhz and set the ...
0
votes
0answers
32 views

arduino atmega32u4 beetle extract hex code

I made a program using the Arduino Atmega32U4. As a security issue, I tried to extract the hex code because I wanted to know if this program was duplicated. avrdude -C"\avrdude.conf" -v -V -...
0
votes
0answers
71 views

ATMEGA32u4 Arduino Bootloader Issues

I've been struggling with this issue for a few days on and off now.  I made a custom PCB (schematic) for a smaller Arduino Pro Micro and it works - mostly.  The only issue I had was that the pins on ...
0
votes
0answers
37 views

Trying to install amforth on Leonardo board

Just got a Arduino Leonardo (with headers) dropped in my lap this week. I've tried experimenting with the Arduino C++ IDE and find it awkward. I have some previous experience with Forth and would like ...
0
votes
0answers
1k views

Can't reset Arduino Pro Micro

I'm trying to reset an Arduino Pro Micro with a new code and it is not allowing me to. I'm using an empty sketch to upload to the pro micro but I get different error messages every time. I think the ...
0
votes
0answers
84 views

Atmega32 push button library problem

I have two files, the first file is a library that I use to handle push buttons and initialize it and the second is where I handle my code and change LED state when push button is pressed, but my code ...
-1
votes
1answer
173 views

Arduino Micro project with Bluetooth low energy

I created my project prototype with Arduino Micro and Adafruit Bluetooth low energy device. Now I need to develop the prototype to production (like a small USB device). I just need Rx, Tx, 3V pin ...