Questions tagged [atmega2560]

Low-power 8-bit AVR microcontroller with 256kB flash.

Filter by
Sorted by
Tagged with
1
vote
0answers
516 views

How to program an SSD1322 display?

I'm new to programming. I would like to change the characters on an SSD1322 OLED display. Here are the photos. Is this possible with an Arduino Uno? Is the program of the display in the display or in ...
-1
votes
2answers
178 views

how can I break from this case by IRremote even if it's not finished yet?

I want to give a pause to case 0xFF02FD or at least to break from that case by entering the case 0xFFA25D even if the 1st case not finished, when I press power button wich has hexa code ( 0xFFA25D) I ...
0
votes
2answers
559 views

ATmega 2560 with Arduino bootloader running issue

I have designed a board based on an ATmega2560 chip and I burned the bootloader by following this tutorial. Now I am able to load Blinky and other programs using an FTDI cable. But the issue I am ...
1
vote
1answer
254 views

Confusion over Transistors for a switching circuit with an Arduino Mega 2560

Apologies if this is a stupid question asked by a noob, but I've looked around to try and find the answer and just can't work it out. Basically, I'm making a project on thingiverse (Glitch's MK2 ...
-1
votes
2answers
202 views

Meaning of part number suffix on top of atmega2560 chip

I have been working on creating a stand alone atmega2560 arduino. When trying to program it with a serial adapter using the rx and tx pins nothing was happening. After a lot of debugging I found the ...
2
votes
3answers
147 views

Conditional randomization gets stuck

First-time poster here... I have the following code to randomize note values and store them in an array loop1[i], where i is a specific step in the loop: nextNote = random(-2, 3); note = note + ...
1
vote
1answer
4k views

Rotary encoder I2C LCD menu

I am trying to make a menu for a monitoring/control system. I am not sure how to make this without interrupting my current code which needs to be monitoring my system at all times to shut off if it ...
2
votes
2answers
382 views

Trying to determine the phase difference between two square signals

I have been looking for the phase difference between two square signals and this is the code: #include <avr/io.h> #include <avr/interrupt.h> void setup() { //Serial.begin(9600); ...
0
votes
2answers
416 views

Burn Bootloader to Chinese Arduino 2560 with AVR ISP programmer

I got my hands on one of these ISP programmer for Atmel AVR microcontroller in USB stick design: Then I selected Progammer > AVR ISP and clicked on Burn Bootloader but it says stk500_recv(): ...
2
votes
2answers
1k views

Arduino MEGA2560 Standalone

I had an Arduino UNO (ATmega168) standalone working, but I need more pins, and I decided to use the ATmega2560, I was searching for some schematics, and none of them shown an ATmega2560 standalone, ...
3
votes
1answer
436 views

Bootloader and Boards Definition for Atmega2560V-8AU at 8 MHz / 3.3v

I am working on a home made project,where i am using Atmega2560V-8AU (note the suffix, this part has an 8 MHz maximum clock rate) as my main controller, supplying 3.3V to this chip. I want this ...
2
votes
2answers
1k views

Programming ATmega2560 processor with FTDI instead of ATmega32

Has anyone tried to program an ATmega2560 with an FTDI chip as is done in the Arduino Nano (this is for a custom design). Will it work?
1
vote
2answers
554 views

7 segment displays arduino mega 2560

I'm trying to use an Arduino Mega 2560 to use 7-segment displays, 6 displays... I use 3 CD4543B to pilot the 6 displays. It works very well for 4 displays as you can see in this video. But when I ...
1
vote
1answer
171 views

Controllino Debugging

Its a well known fact, that you can debug your arduino board with the help of an Atmel Ice. However, you might know the Controllino which is an arduino compatible device. It has an ATmega2560 on it. ...
1
vote
2answers
2k views

Read and store data with the usb

Hi i am new to Arduino and I want to know if it is possible to read the data from a sensor that it is connected to the Arduino, I am using the Arduino mega 2560, which is already working, as I have a ...
2
votes
2answers
1k views

Error while boot loading Atmega 2560 using Arduino Mega 2560

I have developed custom board using Atmega 2560. I am doing boot loading process using the process of migrate from an Arduino board to a standalone microcontroller. I have followed this steps... 1) ...
0
votes
1answer
293 views

Atmega2560 USART UDR r/w conflict possible?

I'm having a really weird issue with my project right now. I have an Atmega2560 using hardware serial, and the software on the other side is doing full duplex read/write at 500kbps. If I change it to ...
2
votes
2answers
376 views

Is there an ICRn CTC mode interrupt vector?

I can use the CTC waveform generation mode to loop to OCRnA and trigger the corresponding TIMER1_COMPA_vect interrupt. // CTC mode TCCR1A &= ~(1 << WGM10); TCCR1A &= ~(1 << WGM11);...
0
votes
1answer
58 views

Value appears to change sign suddenly

When slot == SLOT_1 is true, speed_value is positive but when slot == SLOT_2 is true, speed_value becomes negative. I printed the value of speed_value immediately after the statement speed_value = -...
3
votes
4answers
2k views

If else statement not mutually exclusive?

When I'm running some test on my encoder motors using the following provided code by Makeblock, it appears that the if..else.. statement is not mutually exclusive ie. I can control Encoder_1 and ...
0
votes
1answer
64 views

Get when a button close the circuit

That seems to be a bit stupid to myself but I can't figure out to get to know when my button is pushed (closed) or released (open). You must know that this not just a simple push button. Actually it ...
5
votes
4answers
2k views

Will an ATmega2560 board be faster than a Uno for hard real-time data logging?

I am designing a hard real-time data logger. The Uno is a bit marginal in processing speed. a) Would it be faster if I changed to an ATmega2560? b) On the datasheet, ATMEGA2560 has 135 instructions; ...
1
vote
3answers
1k views

Understanding writing to input pins and pull up resistors

I am new to Arduino, and am trying to understand the following code. The question is: Is my understanding correct, or if not, what is happening here? I have to reverse engineer an existing ...
-1
votes
1answer
101 views

What software should I use to program my ATmega2560? [closed]

I have written code in Atmel Studio 7. First off, I have to create a hex file of the code. How to create a hex file using Atmel Studio 7? Secondly, I want to upload the code to my ATmega2560, so ...

1 2
3