Questions tagged [atmega2560]

Low-power 8-bit AVR microcontroller with 256kB flash.

27 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
0answers
119 views

How to wake up Arduino with an rtc?

I am doing a data logger with an Arduino Mega2560 and I want to use a code to make it sleep when no measure is needed and wake it up with an RTC when time comes. The reason I want this is because I ...
1
vote
0answers
90 views

Advice needed for powering Multiple HX711 with Arduino Mega

I have a project where I need to use multiple load cells (6-8), with individual HX711 for each load cell, which need to be powered simultaneously. I am not sure if I can power all the HX711 with 5V ...
1
vote
0answers
88 views

Erasing all flash on boards with over 64kb of program memory

I'm using a Mega2560 board. My project needs to store some large constant data. To preserve the first 64kb flash chunk, I write these data on addresses beyond this limit. But there is either an ...
1
vote
0answers
58 views

Is there an easy way to connect and control 3 servos?

I need to connect and control three Parallax Standard Servos to an Arduino board, and apart from the USB connection, nothing else will be connected to the board. My predecessor used a setup of and ...
1
vote
0answers
215 views

Intermittent wifi/hotspot connection

I have an Arduino Mega 2560 with a cc3000 Wifi shield that is sending messages to dweet.io. Here is the relevant portion of my code: // Post data to dweetio char data[125]; sprintf(data, "?t1=...
1
vote
0answers
111 views

Arduino not responding while trying to flash over BLE

I'm working on wireless uploader for Arduino from iOS devices. I'm using HM-10 BLE module which seems to work ok. PIO 2 is used as DTR for resetting (see A [0x41] T [0x54] + [0x2B] P [0x50] I [0x49] O ...
1
vote
1answer
221 views

Did I just brick my ATMEGA 2560?

I bought an ATMEGA2560 on eBay and programmed it with Arduino IDE 1.6.9 using the USB cable, and the LED blinked as expected - All well and good. Now I wanted to program the mega from my UNO as ...
0
votes
0answers
11 views

I am trying to rewrite an RFID with a MEGA2560 and a RFID-RC522

I have been trying to rewrite an RFID tag so it is the same as my other one. I have code that will read both separately but I cannot find any already written for the MEGA2560 that will work for me. ...
0
votes
1answer
29 views

Activating a defined macro in a class from main.cpp

Sorry if this question been asked. I'm trying to activate certain function in a class using a macro defined in the class from main.cpp. I'm using jrowberg MPU6050 library if that matters. main.cpp #...
0
votes
0answers
49 views

Problem with I2C

I trying to make a project to write and i2c display from a renault megane vehicle. There is many people showing it but there is no code that i can use. So i buy a cheap analyzer and i can clearly see ...
0
votes
0answers
34 views

Using SMS to receive password, then to choose whether to turn the relay on or off

I'm trying to use SMS messages to turn a relay on/off but before doing that i need to have a password system before allowing the user to turn the relay on/off. Basically, you have to send the password ...
0
votes
0answers
62 views

Arduino code does not function when relays are powered

I have a mega arduino, which is supposed to to power 4 relays using 4 touch sensors TTP 223, the relays are 5V coil and 220V. the arduino is powered by a 5 V adapter "mobile phone charger" and it ...
0
votes
0answers
483 views

OneWire with DS18B20 digital sensor only works on the I2C (20 and 21) pins of my Mega?

I am using an Arduino Mega to read a DS18B20 temperature sensor using the OneWire library in the code below which I got here: #include <OneWire.h> #define DS18S20_Pin 20 //DS18S20 Signal pin ...
0
votes
0answers
51 views

Programming AFE4404 using Arduino mega2560

I'm facing difficulties programming an AFE4404 using the arduino mega2560. I'm using AFE4404 I2C to program it. I tried most of the code I found online with minor changes to get all the LED and ...
0
votes
0answers
52 views

MEGA2560 only starts program after pressing RESET button multiple times

I am working on a program where I am controlling an MP3 player by using UART between my MEGA2560 and the MP3 player. The MEGA2560 sends serial commands to the MP3 player when external interrupts are ...
0
votes
1answer
189 views

Adafruit Micro-SD breakout not initializing on MEGA 2560

] [I am having quite a bit of trouble trying to get my Arduino MEGA 2560 to read my micro-SD card. My wiring is as follows: Breakout Arduino 5v 5v Gnd Gnd CLK 52 DO ...
0
votes
0answers
34 views

Min/Max current for supply input of mega2560

What is the min and max current the mega2560 can take for the 5v supply input voltage of the chip itself, not just the arduino mega?
0
votes
0answers
131 views

EEPROM.read data not comparing with DHT11 sensor value - Arduino temp controller

I'm using a DHT11 to read temperature to control a relay that will control a fan. When 'A' is pressed it allows the user to update the temp value that the relay will go HIGH at. The value is being ...
0
votes
1answer
2k views

How to program the Robotdyn Mega 2560 PRO MINI?

I want to program the Robotdyn Mega 2560 PRO MINI which has no USB port. How do I connect the pins to an FTDI? Which setting do I have to use in the Arduino IDE?
0
votes
0answers
100 views

Sketch works on MEGA 2560 timer2, but does not work on timer1

I set the PWM frequency on MEGA 2560 like this: TCCR2A = 0; TCCR2B = 0; TCNT2 = 0; TCCR2A = _BV(COM2A1) | _BV(COM2B1) | _BV(WGM20); ...
0
votes
0answers
410 views

How to use watchdog timer for the purpose of recovery from failures in Arduino ATmega2560

Here is my tool-set; Visual Studio with plugin called "Visual Micro" Flashing the HEX file using Atmel Studio. via AVRISP mkII on ATmega 2560 MCU And my simple trial code (I have also some others). ...
0
votes
1answer
65 views

What are the negative PINs for on the IndustrialShield M-Duino 58 Analog

I am working as an internship on an Arduino based PLC. It is the M-Duino 58 Analog from IndustrialShields. I try to figure out how it works; Reverse Engineering. But i dont know why it has negative ...
0
votes
0answers
441 views

How to program an SSD1322 display?

I'm new to programming. I would like to change the characters on an SSD1322 OLED display. Here are the photos. Is this possible with an Arduino Uno? Is the program of the display in the display or in ...
0
votes
1answer
55 views

Which board's bootloader is on the microcontroller?

Currently I'm doing a project that needs an Atmega2560 standalone MCU. After I burned the bootloader with this method: http://www.gammon.com.au/bootloader . I set the Board as "Arduino/Genuino Mega or ...
0
votes
2answers
142 views

Is an atmega 2560 board compatible with the Adafruit Trellis?

I want to build a custom midi controller for my computer, and yes, Adafruit has a mini Untz project. For my purposes, I need more analog inputs than the Leonardo, and the only other option I can find ...
0
votes
1answer
56 views

Value appears to change sign suddenly

When slot == SLOT_1 is true, speed_value is positive but when slot == SLOT_2 is true, speed_value becomes negative. I printed the value of speed_value immediately after the statement speed_value = -...
-1
votes
1answer
44 views

Controller freezes

I am using atmega 2560 as main(master) controller and other 5 salve 2 atmega 8 and 3 atmega 328p, there is two device with analogue output connected to main controller atmega 2560 through ads1115 ...