Questions tagged [arduino-nano]

The Arduino Nano is a small board based on the ATmega328 or 168. It has male headers, so it can be plugged directly into a breadboard. It is small and compact, and features a USB chip.

Filter by
Sorted by
Tagged with
0
votes
1answer
76 views

Macbook Pro CH340 Nano 14201 error

I'm using a MacBook Pro Mojave 10.14.6 to code genuine Arduinos. Been working with multiple Uno R3s, no issue. Got a genuine Nano and get the following error: ser_open(): can't open device "/dev/cu....
1
vote
1answer
62 views

Connecting arduino with MATLAB

I installed Octave support package for Arduino and it is listed in the packages installed when pkg list command is run.But when the command "a= arduino('COM8')"; is run,"error: serial: Error opening ...
0
votes
0answers
41 views

Arduino to AtTiny change of pin interrupt behaviour?

I have a project which, to save on battery, is put to sleep until an interrupt pin is rising from LOW to HIGH. This works well on Arduino Nano, however the translation doesn't on the ATTiny. #include &...
2
votes
1answer
110 views

Arduino Project Interrupt Error?

I have a project to be made i.e. water Billing System using RFID(Mfrc522) on Arduino NANO. There is one difficulty that I haven't been able to overcome. I hope someone could help me out. Project flow: ...
3
votes
3answers
3k views

Arduino Nano - programmer is not responding

I cannot seem to upload the simple blink program to my Arduino Nano. I keep getting the message: avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 1 of 10: not in ...
3
votes
1answer
64 views

How to program Esp8266 remotly via wifi?

I hope it's not a sci-fi for arduino. But I saw that dual system with two MCU can program each other via radio connection. It has been done in experimental space cube projects. It is theoretically ...
1
vote
2answers
74 views

I cannot upload any code to my arduino nano

Arduino: 1.8.13 (Windows Store 1.8.42.0) (Windows 10), Board: "Arduino Nano, ATmega328P" Sketch uses 934 bytes (3%) of program storage space. Maximum is 30720 bytes. Global variables use 9 ...
-1
votes
4answers
12k views

Cannot upload sketch to Arduino Nano

I've been using Arduino UNO for quite sometime and brought a new Arduino Nano. When I connected it to my computer, the power usb lit up and the blink sketch started running ( as expected of course). ...
0
votes
0answers
37 views

Is IMU of the Arduino Nano 33 BLE Sense good enough to measure acceleration?

I have to measure acceleration wirelessly for 1 or 2 seconds with a high level of precision. I appreciate any other suggestions.
-1
votes
1answer
31 views

Wiring up an ESP 01 to Nano

I've been at this for over a week now and still cant get things working. Im attempting to wire up an ESP-01 chip to a Nano to send AT commands over Serial. I've followed many different tutorials, but ...
1
vote
1answer
38 views

Arduino Nano stucks on uploading [duplicate]

I'm trying to upload an simple blink sketch to my Arduino Nano, which not used for a while. As I remember, I uploaded an sketch to control RF module, at the last time I used. Now, when I connect my ...
-2
votes
4answers
498 views

SSD1306 recognized in I2C scaner, can't get it to display

The gist of my issue is in the title. I have a cheap ebay SSD1306 128x64 display which I hooked up to my arduino, and checked the wiring at least 50 times and the address is correct, the display has ...
1
vote
1answer
45 views

Help in personal alarm clock project, cant write time on seven segment display

i'm trying to make a type of Arduino alarm clock, which when the time I inputed is equals to the current time, a servo will turn on my lights. It basically consists of a Keypad, an RTC DS1307 and a ...
0
votes
2answers
39 views

TPIC6B595 Output Unable to Allow Supplied Power to 7-segment Display

We have an Arduino Nano connected to 4 small (0.5") common-anode 7-segment displays and 2 large (3") common-anode 7-segment displays. We are trying to multiplex the displays. The larger one ...
1
vote
1answer
43 views

Photoresistor help

I'm a newcomer to Arduino, trying to read analog values from a circuit with a photoresistor. I believe I am using a 1-ohm resistor The problem I am having is that my photoresistor does not seem to be ...
1
vote
0answers
19 views

How to use a non-adafruit BMP280 sensor for continuous data outflow

please I need help with the arduino BMP280 breakout board I got from AliExpress. I’m pretty new to the arduino world, I need it for my rocket datalogger, I downloaded the adafruit BMP280 library but ...
1
vote
0answers
23 views

Dual Channel Reading with 16 bit AD7705(SPI)

I want to read 2 separate voltage readings by AD7705 ADC and send the data to Arduino(Master). What is the correct program flow should I implement to get dual-channel operation working. How data will ...
0
votes
2answers
3k views

Dim a led using a NPN transistor

I know there are a lot of questions about this topic, but I've tried everything and any possible guide online without success. I want dim (increase and decrease the brightness) some leds (3.5 Watt ...
0
votes
1answer
168 views

Arduino Nano Fried on Music Reactive Led Strip

I'm doing a project that involves an Arduino Nano, a sound detection microphone module and a RGB Led strip (individually adressable leds). I also bought an accumulator so I can connect everything ...
1
vote
0answers
102 views

Unable to hear the click sound from the relay [closed]

I am using a 5v 2 channel relay module with arduino nano to turn on and off using RTC. I am able to see the LED on the relay turn on but unable to hear the click sound and the relay does not turn my ...
1
vote
1answer
430 views

Arduino random LED on

I have a project which has two options No. 1 Randomly turn on one LED from a group of 6 LED (Relay Board) No.2 randomly turn on one LED from a group of 2 LED (Relay Board) The selection of the ...
1
vote
1answer
70 views

How can I read this digital pin for Nano by using AVR's Atmel Studo?

How can I read digital pin 6 in AVR? I set the pin as input as follows: DDRD = B0100000; //this will set pin 6 as input But how can I now digital read this pin?: Another way of putting it: how can ...
0
votes
1answer
56 views

Everything is ready for project . I have one doubt! I am using transmitter + Arduino *Uno*..and receiver + arduino *nano* will it work?

Everything is ready for project except hardware! I have one doubt! I am planning to use transmitter of Arduino Uno and receiver of Arduino Nano. Will it work? Both Uno and Nano obey for same ...
0
votes
1answer
68 views

Can i exchange my arduino nano for an atmega328p-pu in my project?

Im currently trying to make a smart light switcher that is attached in front of my rooms light switches. It basically mostly consists of two servos (to turn on or off either switch), two button (to ...
0
votes
2answers
38 views

An array of existing arrays

I have a bunch of 3D arrays in the following form: byte lines[][4][2] { { {B00000000, B11110000 }, {B00000000, B11110000 }, {...
0
votes
0answers
22 views

Use serial communication on Sparkfun SAMD21 mini board

I am working on an economic module to be able to use serial communication with the Sparkfun SAMD21 mini development card. And I have one, the DTR (of my CH340G) do I have to connect it to the reset of ...
1
vote
1answer
54 views

Arduino Nano IoT 33 Char Array size constraints

I would like to save data that I am receiving from API calls in a char array. The problem is the data is around 80KB however my Arduino IoT 33 has 32KB of memory. It will save data in a char array ...
4
votes
1answer
100 views

Arduino timer interrupts for PID

I'm working on a robotics project where an arduino nano is acting as the motion controller. I'm trying to use a trapezoidal motion profile generator and PID loop to follow that profile, but I found ...
1
vote
1answer
267 views

MAX30100 not working

I am unable to get the MAX30100 sensor to work It keeps throwing the following error: 16:06:32.936 -> Initializing... 16:06:32.936 -> MAX30105 was not found. Please check wiring/power. I am ...
0
votes
0answers
23 views

0.96 oled i2c display not working with my Arduino Nano [duplicate]

So what I've tried is: Changing the i2c address from 0x3D to 0x3C and it still doesn't work. Ive also tried an i2c scanner and it hasn't worked either. First I connected the screen like this: GND-...
1
vote
2answers
55 views

Is it possible to send 2 or more o/p signal at the same time?

I wanted run two motors using Cytron MDD10A Dual Channel motor driver. So my concern is based on execution of code that is done line by line, in that case when I'm driving two motors will this delay ...
1
vote
1answer
70 views

Can Arduino UNO permanently store a code?

I'm really new to Arduino and wanted to know if I can make Arduino a permanent controller? and could you help me with a cheaper alternative? I also wanted to know about "fuse", i read it ...
0
votes
1answer
57 views

Do Arduino Nano Every devices short out?

I have an Arduino Nano Every device that seems to have shorted out. I use a lighted USB hub with buttons that turn connections on and off. Each button has its own LED that indicates power state for ...
1
vote
1answer
32 views

How to load scal factor external to the code?

We know that, we need calibration factors (scale factors) to read current sensor data (ACS758) to arduino. I am also using voltage reader using voltage divider circuit for my project. I need to build ...
2
votes
1answer
54 views

Converting from Float to Int yielding weird results. What am I doing wrong?

So I am trying to take GPS data with a Neo 6M gpsmodule (that is what is covered up by the square for privacy sake) and process it by adding/multiplying to get large integers representing the GPS data....
0
votes
1answer
75 views

Can't Upload Sketches to Arduino Nano Every

first-time builder here. I just got my Arduino Nano Every in the mail from Mouser, and I'm trying to upload a modified version of the blink example to my new brand-new board. However, every time I ...
0
votes
1answer
30 views

Will Setting Interrupt Pin High Damage Bluetooth Module?

I want my HC05 Bluetooth Module to trigger an interrupt when it receives a signal. So I've followed suggestions from the Arduino Forum and connected the Bluetooth TXD pin to the Arduino RX Pin and the ...
0
votes
0answers
51 views

Arduino Wont Run Program at 4 Mhz

I want my Arduino Nano to consume as little power as possible, so I have been lowering the clock frequency with CLKPR from the default 16 MhZ speed. I successfully ran the program at 8 Mhz by setting ...
1
vote
0answers
40 views

Is it possible to connect Longan Nano with WS2815 LED stripde?

I have a very interesting interface card - Longan Nano and a LED stripe WS2815 (12V). As far as I understand, I need to connect to DI pin of the LED stripe some pin from SPI output of the card. As the ...
2
votes
1answer
49 views

PT2257 only gives me heavy buzzing sound

I have this project where I control a bluetooth audio module with an arduino. In this case, I have used an arduino nano. But then, I have been meaning to add volume control to the project so I use a ...
1
vote
1answer
66 views

Why does the LEDs affect Analog Input?

So I'm working for a project to control RGB Led Strip using microphone or sound sensor with Arduino Nano. I'm using 5050 RGB Led Strip around 120 LEDs, and I control them using simple transistor ...
0
votes
1answer
120 views
2
votes
2answers
768 views

Arduino Nano 33 IOT issue

Nano 33 IOT is not detecting by windows . When i plug the usb cable only green light on the board. Board is installed from the board manager. the cable is usb DATA cable and not charging cable. I ...
-1
votes
1answer
72 views

“No I2C devices found” Arduino Nano Every

I was able to set up a Arduino Nano with an I2C board very easily, but the Arduino Nano Every is giving me a much harder time (my project required low profile). Just to test, I stripped some wires, ...
1
vote
2answers
154 views

Wireless Bluetooth USB HUB using Arduino nano

I have the following problem/idea: I have a electronics workbench and a separate PC desk. Now I have a USB HUB on the workbench, but it doesn't properly work, because the USB-cable to the pc is too ...
3
votes
1answer
183 views

Arduino nano 33 ble vs ble sense. Power consumption, etc

After working with an Arduino Uno at work, I am looking to buy myself a board for some projects/experiments at home. The nano size seems like a great option, especially the one without soldered ...
1
vote
1answer
151 views

led chaser fill color effect

Please help. I am learning a lot about Arduino. Most all in lightning. I am a newbie. I play with nano and LED ws2812 and use fastled library. What ask is to make effect like fill effect. For ...
1
vote
0answers
21 views

Ardunio wireless voice transmission

I made a project based on calling with gsm module and arduino and now i want to transmit to voice wirelessly to my bluetooth earphone which module should i use for this purpose.
2
votes
1answer
36 views

Communication between ESP01 Arduino NANO and using External Interrupt in Arduino NANO for other than communication program same time

I have done communication between ESP01 and Arduino NANO (ATMEGA328 based). ESP pins used are GPIO-0 and GPIO2. In NANO, used D2 and D3. This program working Ok. Now I want to add external interrupt ...
1
vote
0answers
31 views

NRF24 receiving data while turned off

The code to set up the nrf24 is from Electronoobs. The further if-clauses are suposed the drive a motor. The problem I am facing is, that if ther is no data transmission (emitter turend off; or ...

1
2
3 4 5
22