Questions tagged [arduino-micro]

A microcontroller board based on the ATmega32u4 with built-in USB communication.

Filter by
Sorted by
Tagged with
0
votes
1answer
92 views

Software I2C - sending data

I'm trying to read a voltage in from a power supply to an Arduino Micro, then send it to an oscilloscope through an I2C (MCP4725). I would use the default pins on the Micro but I want to wire three ...
2
votes
1answer
523 views

What's the problem with baudrate?

I was trying to evaluate the speed of communication between pc and Arduino, using this code in Arduino: void setup() { Serial.begin(9600); } void loop() { Serial.println("Ciao Arduino"); } and ...
3
votes
2answers
207 views

Arduino-based mains frequency monitor follow-up

Following my previous question, I'm getting closer to thinking about putting together this mains frequency monitor. I would just like to do a sanity check on my electronics before I order the ...
3
votes
3answers
573 views

How to have some code executed at a certain time of day with a DS3231 RTC?

I recently bought a DS3231 RTC, but I cannot seem to figure out how to get it to work. I have tried all different tutorials and example programs but I keep getting 2165.25.165 165:165:165 as the ...
7
votes
3answers
25k views

Are there any reasons to pick Nano over Micro?

Nano is from 2008, and micro from 2012. Micro seems better on every parameter, in particular in having a better (I think) microcontroller, ATMega32u4, over ATMega328P. However, all the shops I've ...
2
votes
2answers
3k views

433MHz sending not receiving

I'm trying to send data using these cheap parts. When I check the voltage on the data port of the transmitter, I see what I expect, 1.2 and 0.6 fluctuating while sending. But when I check the ...
1
vote
2answers
727 views

Hardware network-infrastructure for a fully-arduino-based home-automation project

As already mentioned in another question, I'm spending LOT of time planning the home-automation system for my new house (currently still in the "still building" phase). Even if started only as a "...
1
vote
2answers
8k views

Arduino Uno vs Arduino Micro timers → pins

Where do I find the pins relative to timers of each individual Arduino microcontroller? As I like Arduino's I already have various samples of them. The one I mostly use is the Uno and Micro for now......
5
votes
2answers
161 views

How to differentiate between 2 Micros on Linux

I have 2 Arduino Micro based devices that I want to use on my Ubuntu Linux machine. I need them to have unique serial ports. Unfortunately, both have the same serial number which makes ...
3
votes
1answer
1k views

How to send unmodulated IR-Signal via cable?

I need to generate en (extended) NEC signal. I have connected an Arduino with a display-device via an IR cable. Arduino --> IR-cable --> IR-input of display device IR-cable: One plug is ...
2
votes
1answer
372 views

Using Arduino Micro With 12V Buzzer

I have an interesting situation. I wonder if anyone can help? I have: 4x Arduino Micros loaded with the basic Blink sketch 5x 12 volt buzzers A desk full of completely fresh Duracell AA and 9v ...
2
votes
2answers
2k views

if(Serial) not working correctly on micro or pro micro

I have an arduino micro and several clone "pro micro"'s both of which are based on the 32u4, i'm trying to make my project have a debug mode which is only active when the serial port is open, the ...
1
vote
2answers
828 views

SoftwareSerial problems

Hi we are using an Arduino Micro and working with a Bluetooth device and a Rfid Scanner from Sparkfun(ID-20 LA). For that we implemented 2 SoftwareSerial objects and the Serial port for the Serial ...
1
vote
2answers
3k views

Unable to flash bootloader on ATmega32U4 with AVR dragon

I am flashing a naked ATmega32U4, but the process fails in the end where it is verifying. avrdude -c dragon_isp -p m32u4 -P usb -U flash:w:Caterina-Micro.hex -U lfuse:w:0xff:m -U hfuse:w:0xd8:m -U ...
0
votes
1answer
3k views

Starting usb on pro micro after deep sleep (ATmega32u4)

I have just started playing with a low power arduino project, and have managed to get the power drain down to about 220uA using powerDown from LowPower. What I would love to be able to do is start ...
0
votes
4answers
370 views

Altering code to run a timer while checking for a data input

I am rather new to the Arduino world and am looking for a way to create my own tipping rain gauge with only one Arduino(micro). I have had some help from a friend to get a loop that checks for when a ...