We’re rewarding the question askers & reputations are being recalculated! Read more.

All Questions

Filter by
Sorted by
Tagged with
0
votes
1answer
22 views

Increasing range of a DC-offset signal (software)

I am trying to read a signal with a DC offset of 511 (as seen by the ADC). The signal's tiny with regards to the offset, and I'm feeding it to a library that does a Fourier transform on it. It comes ...
0
votes
1answer
274 views

Arduino Due ADC negative voltage

I’m trying to sample an AC signal on the Arduino Due. The AC signal will never exceed +-80mv across a frequency range of 6-833Hz. Current is negligible. I believe there are clamping diodes to protect ...
0
votes
1answer
99 views

If I use a biasing circuit for a signal going into an analog input pin, will it affect the ADC operation?

If I have a single 100Hz AC signal biased by two 1 M-ohm resistors (as per schematic below), and then output to an Arduino UNO analog input pin, with the UNO sampling at around 1 kHz using delays, ...
2
votes
2answers
427 views

Lowest voltage applicable on AREF pin on Uno and Mega

I need to measure an Analog signal in the range of 5-30 mV. Naturally, using the internal default 5V reference leads to very poor measurement resolution. I would like to use the capability to use an ...
0
votes
1answer
130 views

External ADC reference when using MATLAB support package for Arduino

I am using the MATLAB support package for Arduino. However, I need to configure the ADC reference to external. MATLAB documentation doesn't really explain how to do this? Is there any way I can use ...
0
votes
2answers
1k views

Interfacing TRRS headphone to Arduino Uno

I have been working in a Arduino project lately which requires human voice input to Arduino with some processing Arduino need to perform specific task. Simple sampling of incoming signal and ...
1
vote
3answers
345 views

AC meter By ADC timer interrupt from Nick Gammon

I want to read ADC from the pin A0 and A1. I have written in this code, however. I took this code came from Nick Gammon Thank You ///////////////////////////////////////////////////////////////////...
1
vote
1answer
264 views

how do you capture the top value in a fallen edge in analogs data (flex sensor)

Guys i'm working with a flex sensor and I'm trying to capture a specific value which is the moment before the user lets go of a flexed flex sensor and its represented as the top point of a falling ...
0
votes
1answer
180 views

How to interpret analog values sent to Arduino from line scanner?

So I have a line scan camera attached to my Arduino Mega and I'm trying to send it a digital clock impulse and get an analog output back. The line scan camera is supposed to return 128 pixels. So far ...
0
votes
2answers
2k views

Arduino Micro + Max4466 - Noise on A0

I've got an Arduino Micro, and a MAX4466 ECM / AMP breakout board (https://www.adafruit.com/product/1063). I'm powering the Arduino Micro from the USB port. On the MAX4466 (to the Arduino), I've ...
1
vote
3answers
782 views

Can do I make an Arduino program that can decipher telephone touch tones?

I have an old land line phone that I want to connect to my Arduino. Then I would like to write a program that can decipher the touch-tone button presses (which are a combination of two tones) so that ...
-1
votes
1answer
632 views

0-1 V input to 0-5 V Output

We have an instrument that has analog output of 0-1 volts and we need to convert this to 0-5 volts. What is the best op amp to use for this and how should the resistors be set up? Any help would be ...
0
votes
1answer
87 views

Arduino AD-converter tolerance

I created a quite simple Arduino sketch: void setup() { Serial.begin(9600); } void loop() { int sensorValue = analogRead(A0); Serial.println(sensorValue); float voltage = sensorValue * (5 ...