Questions tagged [analog-sampling]
In signal processing, sampling is the reduction of a continuous-time signal to a discrete-time signal. A common example is the conversion of a sound wave (a continuous signal) to a sequence of samples (a discrete-time signal). A sample is a value or set of values at a point in time and/or space.
11
questions with no upvoted or accepted answers
2
votes
0
answers
688
views
Using Analog Comparator on Uno to Read Differential Voltage Signaling
I am trying to use the Arduino Uno to read an AVCLan bus on a Toyota vehicle. Logic 0 is when +/- drive are 120mV or more apart, and logic 1 is 20mV or less. See Toyota AVC-Lan description.
I ...
- 121
1
vote
0
answers
114
views
Problem with sending sound sensor data to app using ESP32 over BLE_UART
I was working on Adafruit Electret Microphone Amplifier - MAX4466 with Adjustable Gain
and ESP32.
I want to send data to an app using BLE UART
I have printed data to the serial monitor or serial ...
- 17
1
vote
0
answers
103
views
How to implementing timer interrupt with a sensor device using A0 and A1 pins
I was wondering if there is a way to program a timer interrupt to collect sensor data at a specific sampling rate?
I want to attach two strain gauge sensors to A0 and A1 pins and collect the data at a ...
- 71
1
vote
0
answers
611
views
Optimizing Teensy 3.6 for data sampling?
So, I have a very basic project where I cycle through 8 IR individual transmitters. After setting the individual transmitter high, I cycle through all 8 IR receivers and print their values, RX_CYCLES ...
- 53
1
vote
0
answers
374
views
AD7606 DAQ and datalogging
I'm making a Data Acquisition System for force impact usign an AD7606 from Analog Devices, an Arduino DUE and a load cell. I already tested it following this guide an making the proper changes for ...
0
votes
0
answers
94
views
Teensy 4.1 Synchronized PWM - ADC sampling
I'm looking to drive a high side driver at PWM frequency of 200Hz on a Teensy 4.1 with variable duty. The high side driver current sense pin is connected to an analogue pin on the Teensy. I want to ...
- 59
0
votes
1
answer
286
views
MCU Recommendations for Audio Pitch Shifting
I'm looking to use a MCU for audio sampling. I want to sample incoming audio and pitch shift it (without speeding it up/slowing it down). A bit about the build. I'm planning to make a circuit board ...
- 9
0
votes
0
answers
2k
views
Reading TCD1304 linear CCD Sensor
I want to read the TCD1304 linear CCD sensor with an ESP32 and I'm facing some problems. As a first "warm-up" and to get familiar with this sensor I tried to generate the sensors input ...
- 1,829
0
votes
1
answer
450
views
Using Arduino to Record analog signals with SPI ADC + Sampling Rate Issue
I am using Arduino UNO to Read 8-channel, 24-bits resolution Analog signals using ADS1299 Analog-fornt-end. ADS1299 use SPI interface to talk with Arduino. Currently, I can record the analog signal ...
- 11
-1
votes
1
answer
133
views
Voltage meter ADC + serial: Bytes lost during communication
I want to make a simple digital voltage monitor. So I have a sketch:
void setup() {
Serial.begin(115200);
}
void loop() {
int val = analogRead(A4); // read the input pin
val = 1;
byte ...
- 133
-1
votes
1
answer
163
views
External ADC reference when using MATLAB support package for Arduino
I am using the MATLAB support package for Arduino.
However, I need to configure the ADC reference to external. MATLAB documentation doesn't really explain how to do this?
Is there any way I can use ...
