0

I see very confusing documentation on powering the arduino mkr 1010. But I would like to know what kind of cable to power (a weird connector port on its side) it with and also can I just put 5 volts + (ac or dc?) into the vin port and connect a ground?

Improve this question
6
  • 2
    what do you mean by weird connector? ... which one are you referring to?
    – jsotola
    Apr 19 at 4:45
  • @jsotola there is only one weird connector on MKR boards :-)
    – Juraj ♦
    Apr 19 at 15:27
  • forum.arduino.cc/t/lipo-connector-for-mkr-series-seriously/…
    – Juraj ♦
    Apr 19 at 17:37
  • 1
    @jsotola it is relative. there are two connectors. one is USB, second is some JST. which one of them is the weird one? :-)
    – Juraj ♦
    Apr 20 at 4:53
  • 1
    @greg your question is not very clear. Please have a read of How to ask a good question and then edit your question to suit.
    – sa_leinad
    Apr 26 at 3:31

2 Answers 2

Reset to default
0

The documentation shows three ways of powering the board see FAQs section Batteries, Pins and board LEDs

  1. Using a USB connector to provide 5V to the board. Typically, this is connected to a USB port on the PC you are using to program the board. Alternatively, a USB cable connected to a standard USB power supply could be used after the program has been loaded.

  2. Using the Vin pin to supply a REGULATED 5V (maximum 6V). Of course, this is DC. Yes, you would also connect the power supply GND to the board's GND pin.

  3. LiPo battery. This is a little more complicated to use safely and there is documentation on that as well - see the app note here to start. You absolutely need to understand how to use a battery with that board - there are safety concerns in this regard that can't be ignored.

Hope it helps.

Improve this answer
2
  • Thank you very much DrG. I am very new to Arduino.. There is no USB port( unless that is the small type "C"? connector on the end). I see the Vin pin and thanks to your " app note" insert I found what I need, a 2-pin JST-PH connector for the battery, now to look for it.
    – greg
    Apr 19 at 16:50
  • found a proper USB connector, on my wifes Kindle. thanks again
    – greg
    Apr 19 at 17:25
0

Just if you are wondering,The mkr1010 uses Micro USB (USB-B) arduino doc says. https://docs.arduino.cc/hardware/mkr-wifi-1010

Improve this answer
3
  • 1
    that is not the weird connector
    – Juraj ♦
    Sep 18 at 4:33
  • Then is it this Battery connector: The connector is of type JST S2B-PH-SM4-TB(LF)(SN). Mating connector is JST PHR-2?
    – V205
    Sep 18 at 23:41
  • This maybe? Additional I2C Port The MKR WiFi 1010 has an additional connector meant as an extension of the I2C bus. It's a small form factor 5-pin connector with 1.0 mm pitch. The mechanical details of the connector can be found in the connector's datasheet. The I2C port, also referred to as the Eslov self-identification port within Arduino, comes with: SDA, SCL, GND, +5V, and an extra digital pin meant to send an alarm to the otherwise plain I2C devices connected to it. The pinout is shown in the following image:
    – V205
    Sep 18 at 23:42

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge that you have read and understand our privacy policy and code of conduct.

Not the answer you're looking for? Browse other questions tagged or ask your own question.