UPDATE: The LCD will light up only when the all my components are located in the bottom right of the breadboard. Why am I not able to use the entire breadboard for my circuit?

I am trying to display data from a temperature and humidity sensor on the serial monitor and the liquid crystal display.

I am using :

  • Arduino Uno R3
  • I2C 16x2 LCD Module
  • 3 pin DHT11 sensor

Here is my code :

#include <dht.h>                // initialize the digital temperature and humidity sensor library ("DHTlib")
#include <LiquidCrystal_I2C.h>  // initialize the liquid crystal display library ("LiquidCrystal I2C")
#include <Wire.h>               // intialize the wire library 

/*   the first parameter is the I2C address
 *   the second parameter is how many columns are on your screen
 *   the third parameter is how many rows are on your screen
LiquidCrystal_I2C lcd(0x27, 16, 2);

dht DHT;              // create a handle to call functions from the sensor library 
#define DHT11_PIN 7   // assign a digital pin number to the sensor 
float TempC;          // create a variable to store temperature in celsius
float TempF;          // create a variable to store temperature in fahrenheit
float Humi;           // create a variable to store humidity

void setup()
  lcd.init();                // initialize liquid crystal display 
  lcd.backlight();           // turn on the backlight of the lcd 
  pinMode(DHT11_PIN,INPUT);  // configure the pin for the sensor as an input for reading the data
  Serial.begin(9600);        // set data rate in bits per second for serial data transmission 

void loop()
  // collect sensor data 
  int chk = DHT.read11(DHT11_PIN);  // store sensor data in a variable
  TempC = DHT.temperature;          // store temperature in Celsius
  TempF = 9 / 5 * TempC + 32;       // store temperature in Fahrenheit
  Humi = DHT.humidity;              // store relative humidity as a percentage

  // display sensor data on LCD 
  lcd.setCursor(0,0);    //tell the screen to write on the top row
  lcd.print("T: ");
  lcd.print(TempC);    // print the temperature in Celsius
//  lcd.print(TempF);    // print the temperature in Fahrenheit
  lcd.print((char)223);  // print the degree symbol 
  lcd.print(" C");         
//  lcd.print(" F");     
  lcd.setCursor(0,1);    // tell the screen to write on the bottom row
  lcd.print("H: ");      
  lcd.print(Humi);       // print the humidity
  lcd.print(" %");  

  // display sensor data on the serial monitor 
  Serial.print("Temperature = ");
  Serial.print(TempC);     // print the temperature in Celsius
//  Serial.print(TempF);     // print the temperature in Fahrenheit
  Serial.print("\xc2\xb0");  // print the degree symbol 
  Serial.println(" C");    
//  Serial.println(" F");    
  Serial.print("Humidity = ");
  Serial.print(Humi);        // print the humidity
  Serial.println(" %");

  delay(2000);  //delay fetching the next sensor values for 2 seconds 

enter image description here

My jumper wires are connected as follows:

  • DHT plus → red plus row
  • DHT middle → digital pin 7
  • DHT minus → blue minus row
  • LCD GND → blue minus row
  • LCD VCC → red plus row
  • LCD SDA → analog pin A4
  • LCD SCL → analog pin A5
  • Red plus row → 5V pin
  • Blue minus row → GND pin
  • Do you not see a breadboard, an arduino board, a liquid crystal display, a sensor, and jumper wires all hooked up?
    – Dev Dhruv
    Apr 2, 2021 at 5:35
  • The picture is unusable, dark and low resolution. Pin names and wire paths are not clearly visible. These allow others to try to identify your problem and it would be a good idea to put some more effort into getting them across clearly. It might also be a good idea to describe your setup in text (such as which pins are connected to which other pins).
    – StarCat
    Apr 2, 2021 at 6:24
  • Btw, it looks like there’s nothing connected to the (I2C) SDA and SCL pins on your Arduino, but it’s hard to make out. There’s also no way to see if the power pins of your LCD are properly connected.
    – StarCat
    Apr 2, 2021 at 6:31
  • All right, I put a new picture, and I explained the setup. Is there an error in my code or in my circuit?
    – Dev Dhruv
    Apr 2, 2021 at 6:31
  • 1
    Did you try moving the knob on the I2C 16x2 LCD Module for changing the contrast? Apr 2, 2021 at 7:27

1 Answer 1


Your breadboard is one of those which have the power/GND lines interrupted between columns 31 and 33. I also once fell into this trap. If you look closely, you see that the blue and red lines are interrupted in the middle of the board. Just put wires between these pins to bridge the gap.

  • Thanks! I never realized my problem was so trivial!
    – Dev Dhruv
    Apr 2, 2021 at 18:15
  • Glad I could help. If this answer helped you, please don't forget to accept it.
    – PMF
    Apr 12, 2021 at 12:08

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.