0

I've tried to copy CH340G from other schematics and existing Arduino Uno Clones... Searched online & StackExchange but no good :/ My problem is almost the same as this one

Here is my schematic

Schematics

I can read & send data from the serial monitor

  • OS: Win 10 64 Bit
  • USB Driver: 3.5.2019.1

Upload Options:

  • Arduino IDE version: 1.8.12
  • Board: Arduino Uno (also tired nano & nano old bootloader options)

What I've tried:

  • With & without the driver
  • Rebooted the computer
  • Tried different ports
  • Different cables
  • In case of IC not working, I've desoldered IC from working UNO
  • Changed RX, TX vice versa
  • Without R1 & R2
  • Different capacitors on C6 and C3 Buuut results are always the same as below
avrdude: Version 6.3-20190619
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM3
         Using Programmer              : arduino
         Overriding Baud Rate          : 115200
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xf3
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xf3
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xf3
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xf3
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xf3
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xf3
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xf3
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xf3
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xf3
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xf3

avrdude done.  Thank you.

Problem uploading to board.  See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.

I appreciate any help, idea, suggestion Regards

Improve this question
8
  • Have you installed the bootloader?
    – Majenko ♦
    May 19, 2020 at 15:22
  • Yes @Majenko, I've burned bootloader and uploaded code via ISP. I can communicate with it already, but can not upload code via USB
    – ahmetertem
    May 19, 2020 at 15:29
  • What else is on the RESET line?
    – KIIV
    May 19, 2020 at 16:14
  • If you can use the CH340 as a Serial-USB bridge (Serial.print and Serial.read work) but you cannot upload a sketch without using a programmer, the bootloader (or fuses) are bad for some reason.
    – DataFiddler
    May 19, 2020 at 16:31
  • @KIIV, 10k resistor like Uno and Nano (5V and reset signals)
    – ahmetertem
    May 19, 2020 at 16:40

1 Answer 1

Reset to default
1

The schematic is totally working. My mistake was after burning bootloader, I was uploading code via ISP. If you upload code via ISP, you're removing bootloader.

Thank you everyone who helped me to I wasn't mistaken at schematic and else...

Improve this answer

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.