0

I'm trying to flash an Arduino Uno using usbasp but i'm getting the following error,I have checked all the connection and voltage using multimeter but still this error:

Arduino: 1.8.8 (Windows 10), Board: "Arduino/Genuino Uno"

C:\Users\SillyMonster\Desktop\arduino-1.8.8\hardware\tools\avr/bin/avrdude -CC:\Users\SillyMonster\Desktop\arduino-1.8.8\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -cusbasp -Pusb -e -Ulock:w:0x3F:m -Uefuse:w:0xFD:m -Uhfuse:w:0xDE:m -Ulfuse:w:0xFF:m 

avrdude: Version 6.3-20171130
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Users\SillyMonster\Desktop\arduino-1.8.8\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : usb
         Using Programmer              : usbasp
         AVR Part                      : ATmega328P
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PC2
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : usbasp
         Description     : USBasp, http://www.fischl.de/usbasp/

avrdude: auto set sck period (because given equals null)
avrdude: warning: cannot set sck period. please check for usbasp firmware update.
avrdude: error: program enable: target doesn't answer. 1 
avrdude: initialization failed, rc=-1
         Double check connections and try again, or use -F to override
         this check.


avrdude done.  Thank you.

Error while burning bootloader.

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.

I have tried different three other Usbasp but still same error

Different USPasp

bumped to the homepage by Community yesterday

This question has answers that may be good or bad; the system has marked it active so that they can be reviewed.

  • This is the same dead programmer from before? Check the traces and connections on the programmer for shorts / open circuits. Also the cable. – Majenko May 12 at 9:58
  • @Majenko It's the dead programmer form before. I am using desktop with Intel Coffee Lake processor and MSI Z370 motherboard, can this cause any problem? – Potato Gamer May 12 at 16:30
  • Take it out of the lake of coffee? Your computer is irrelevant. The fact that you have a known dead programmer is all that matters. – Majenko May 12 at 16:30
  • @Majenko Thanks – Potato Gamer May 12 at 16:32
  • @Majenko i just need to flash the boot loader on an arduino uno, this time i'm using Arduino as ISP and getting this pastebin.com/3FhQfA6R, Connection: IMG1 IMG2 – Potato Gamer May 12 at 16:56
0

The problem was with the Arduinos i have received from AliExpress All of them are using WAVGAT AVGA 328P-AU chips. I flasthed other Atmel MEGA 328P chip based Arduinos using USbasp and it's working fine. But i dont know how to flash those WAVGAT AVGA 328P-AU chips.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.