0

I tried many ways to get and print UID and other data from MIFARE Ultralight but it always ends with error. I am using RFID-RC522 reader with Arduino UNO and MFRC522 Library. I can normally get and print the PICC type of chip, but that's the only thing that works.

That's how I have connected my RC522 reader:

enter image description here
(source: ytimg.com)

This is my code:

#include <SPI.h>
#include <MFRC522.h>

#define RST_PIN 9
#define SS_PIN 10

MFRC522 rfid(SS_PIN, RST_PIN);

unsigned long noSignal = 0;

bool lastState = true;
bool read = true;

void setup()
{
    pinMode(2, OUTPUT); //Red led
    pinMode(3, OUTPUT); //Green led

    Serial.begin(9600);
    SPI.begin();
    while (!Serial);

    rfid.PCD_Init();
    Serial.println("RFID ctecka byla uspesne spustena."); //Prints "RFID Reader succesfully started"
    Serial.println();

    changeLed(true);
}

void changeLed(bool red) 
{
    digitalWrite(2, red);
    digitalWrite(3, !red);
}

void loop()
{
    if (millis() - noSignal >= 300) 
    {
        changeLed(true);
        read = true;
    }

    bool state = !rfid.PICC_IsNewCardPresent() && !rfid.PICC_ReadCardSerial();

    if (state != lastState)
        if (state)
            noSignal = millis();
        else if (read)
        {
            read = false;

            changeLed(false);
            noSignal = millis();

            Serial.println("---------Cip detekovan----------"); //Prints "Chip detected"
            Serial.println();

            MFRC522::PICC_Type piccType = rfid.PICC_GetType(rfid.uid.sak);

            Serial.print("Znacka cipu: ");//Prints chip type
            Serial.println(rfid.PICC_GetTypeName(piccType));

            rfid.PICC_DumpToSerial(&rfid.uid); //Here is the error

            Serial.println();
            Serial.println("---------Cteni skoncilo----------");//prints "Read ended"
            Serial.println();

            rfid.PICC_HaltA();
            rfid.PCD_StopCrypto1();
        }

    lastState = state;
}

Serial monitor snapshot:

Maybe important thing is that when i call PCD_DumpVersionToSerial() i get:

Firmware Version: 0x12 = (unknown)

Somewere I read that my Arduino isn't compatibile with MIFARE Ultralight and I need MIFARE Classic cards. Is that true? Can I solve this problem by using other library or it's hardware problem? Thanks

Btw. Sorry for my english, it's not my native language.

EDIT: I asked my friend, which have arduino too from same shop like me, if he can read MIFARE Ultralight cards. He said that it's working for him. So my problem will be probably on hardware side. We both have unoficial arduino from aliexpress.

1 Answer 1

2

In the first lines of code there are two lines that say:

#define RST_PIN 9
#define SS_PIN 10

They define the RESET pin to be on the D9 pin and the SDA on the D10 pin. So you have an connection error try connecting like shown and you should be good to go.

default connection

5
  • Sorry, I made mistake. I have connected pins like in your picture. I will update my question.
    – mozkomor05
    May 11, 2018 at 17:21
  • @DavidMoškoř have you tried the original example?
    – Coder_fox
    May 11, 2018 at 17:33
  • Yes, same result
    – mozkomor05
    May 11, 2018 at 17:35
  • Is it possible that my cards are using encryption DES3 that my arduino cannot decrypt?
    – mozkomor05
    May 11, 2018 at 17:37
  • @DavidMoškoř it is possible that your card use a different frequency.
    – Coder_fox
    May 13, 2018 at 8:00

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge that you have read and understand our privacy policy and code of conduct.

Not the answer you're looking for? Browse other questions tagged or ask your own question.