2

I am trying to work with the (new) sparkfun razor IMU 9dof, I wrote a silple sktetch to calibrate the magnetometer:

#include <SparkFunMPU9250-DMP.h> // Include SparkFun MPU-9250-DMP library
#include <Wire.h> // Depending on your Arduino version, you may need to include Wire.h
MPU9250_DMP imu; // Create an instance of the MPU9250_DMP clas
void setup() {
  Serial.begin(115200);

  Serial.println(F("Adafruit 10 DOF Board AHRS Calibration Example")); Serial.println("");

  if (imu.begin() != INV_SUCCESS){
    while (1) {
    Serial.println("Failed to initialize MPU-9250, loop forever");
   }

  }

 imu.setGyroFSR(2000); // Set gyro to 2000 dps

 imu.setAccelFSR(2); // Set accel to +/-2g

 imu.setLPF(5); // Set LPF corner frequency to 5Hz

 imu.setSampleRate(100); // Set sample rate to 10Hz

imu.setCompassSampleRate(100); // Set mag rate to 10Hz
}

void loop(void){
  imu.update();

  // Print the sensor data
  Serial.print("Raw:");
  Serial.print(imu.ax);
  Serial.print(',');
  Serial.print(imu.ay);
  Serial.print(',');
  Serial.print(imu.az);
  Serial.print(',');
  Serial.print(imu.gx);
  Serial.print(',');
  Serial.print(imu.gy);
  Serial.print(',');
  Serial.print(imu.gz);
  Serial.print(',');
  Serial.print(imu.mx);
  Serial.print(',');
  Serial.print(imu.my);
  Serial.print(',');
  Serial.print(imu.mz);
  Serial.println();  

  delay(50);
}

To be sure the Arduino IDE can access to dev/ttcACM0, I did sudo chmod 666 /dev/ttyACM0

I can dowload successfully but when I want to open the terminal I got the following error:

Erreur d'ouverture du port série « /dev/ttyACM0 ». (Port busy) (see attached screenshot)

More over when I entered dmesg on the console, I can see the following messages:

[   94.133923] usb 3-2: USB disconnect, device number 2
[   94.133978] cdc_acm 3-2:1.1: urb 12 failed submission with -19
[   94.135862] cdc_acm 3-2:1.1: urb 13 failed submission with -19
[   94.136059] cdc_acm 3-2:1.1: urb 14 failed submission with -19
[   94.136257] cdc_acm 3-2:1.1: urb 15 failed submission with -19
[   94.136457] cdc_acm 3-2:1.1: urb 2 failed submission with -19
[   94.136656] cdc_acm 3-2:1.1: urb 3 failed submission with -19
[   94.136852] cdc_acm 3-2:1.1: urb 5 failed submission with -19
[   94.137048] cdc_acm 3-2:1.1: urb 6 failed submission with -19
[   94.138841] xhci_hcd 0000:03:00.0: WARN Cannot submit Set TR Deq Ptr
[   94.138843] xhci_hcd 0000:03:00.0: A Set TR Deq Ptr command is pending.
[   94.931853] usb 3-2: new full-speed USB device number 3 using xhci_hcd
[   95.316578] usb 3-2: New USB device found, idVendor=1b4f, idProduct=9d0f
[   95.316581] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   95.316582] usb 3-2: Product: SFE 9DOF-D21
[   95.316584] usb 3-2: Manufacturer: SparkFun
[   95.320306] cdc_acm 3-2:1.0: ttyACM0: USB ACM device
[  858.774849] usb 3-2: USB disconnect, device number 3
[  904.529058] TCP: wlp1s0: Driver has suspect GRO implementation, TCP performance may be compromised.

Does anyone outhere experienced such issue?

Thank you for your help

Fabrice

Improve this question
3
  • 2
    Remove the modemmanager package.
    – Majenko ♦
    Dec 6, 2017 at 15:57
  • 1
    Also you should add your user to the group which owns serial devices - the chmod trick would have to be repeated every time you reboot or replug the board. Finally, you can use lsof | grep ttyACM to see which process is holding the port (might possibly need to run lsof as root, but try it first as yourself)
    – Chris Stratton
    Dec 6, 2017 at 17:40
  • 1
    Just to odd simple things out first: have you closed all serial monitors in other instances?
    – Sim Son
    Feb 21, 2019 at 16:41

4 Answers 4

Reset to default
5

sudo apt-get purge modemmanager It helps me for linux user and for many other peoples. Now I am playing with stm32f103 and opening port was painfull. That was problem only for stm32 chip. Arduino nano was working without problems. Before I need reopened few times port to initiate communication. That was painfull. After finding that solution now Arduino ID is working without problems. I am not sure if deleting modemmanager will have impact for my system.

Improve this answer
2

I solved following serial port related problems in ubuntu 18.04 as follows:

Problem 1 : Cannot open /dev/ttyACM0: Permission denied
Solution : Grant permissions to read/write to the serial port with this terminal command ---> sudo chmod a+rw /dev/ttyACM0 Here replace tty port with your respective ubuntu port.

Problem 2 : Failed to open /dev/ttyACM0 (port busy) Solution : This problem appears when serial port is busy or already occupied. So kill the busy serial port with command ---> fuser -k /dev/ttyACM0. Here replace tty port with your respective ubuntu port.

Problem 3 : Board at /dev/ttyACM0 is not available Solution : In this case, your serial port in tools menu will be greyed out. I googled a lot for this, but none of solution worked for me. Atlast I tried different arduino board and usb connector and it was working for me. So, if you are having old arduino board (can be solved using required drivers) or defected arduino board then only this problem arises.

Improve this answer
1

When I had this problem I discovered that running ps x showed a lot of tasks involving temporary mount files. So I closed Arduino, ran sudo rm -rf /tmp/.mount_arduin* and restarted Arduino. The device attached successfully.

Improve this answer
1

You need to be part of the dial out group. Try this: Type 'groups', is 'dialout' there ? sudo usermod -a -G tty yourUserName Example sudo usermod -a -G tty gil

Log off and log on again for the changes to take effect. This has consistently worked for me and is now in some of the Arduino install packages.

Improve this answer

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge that you have read and understand our privacy policy and code of conduct.

Not the answer you're looking for? Browse other questions tagged or ask your own question.