https://i.sstatic.net/cCeV8.png

Ok, MAYBE I solved it^^ so the thing is, i noticed that my LED is still blinking intense instead of 2 sec light off and on. which means that i am still not in AT Mode.

but the thing is if i followed Instructables and other website tutorial. I SHOULD be able to be in AT Mode. im not exactly sure why im still not in AT Mode. So tried something:

the wiring/circuit is still THE SAME. but add something: I took another wire, connect the EN Pin of HC-05 -> 5V of Arduino. since days ago i was trying to do tinker my HC-05 here and there and i remember that i tried to put EN in 5V then it start blinking differently. so i tried the same thing today. then i went back and Forget Paired Device, connect my Arduino to my Laptop, then reupload my code, then go to Serial.Monitor 9600 set No Ending Line -> Both NL & CR. then i reenter the AT Commands.

AT+NAME? then AT,then AT+PSWD? all worked. the AT+Name shows the name of my HC-05, and the AT+PSWD shows the password. so then i decided to finally rename my HC-05. AT+NAME=USER and AT+PSWD=ARDUINO and now my HC-05 has different name and password. i then went to my Phone, scan for bluetooth device and there it is. USER_HC05 and password is ARDUINO.

^^what im not really sure if it is the solution im searching for. i searched some tutorials again but none of them mention of using EN Pin and most of them use STATE Pin of HC-05.So because of that, i wont "Check" this Answer as maybe this is not the best solution out. maybe just not yet. but it did solve MY problem so it may solve other users problem too so ill add it here to inform.

Ok, MAYBE I solved it^^ so the thing is, i noticed that my LED is still blinking intense instead of 2 sec light off and on. which means that i am still not in AT Mode.

but the thing is if i followed Instructables and other website tutorial. I SHOULD be able to be in AT Mode. im not exactly sure why im still not in AT Mode. So tried something:

the wiring/circuit is still THE SAME. but add something: I took another wire, connect the EN Pin of HC-05 -> 5V of Arduino. since days ago i was trying to do tinker my HC-05 here and there and i remember that i tried to put EN in 5V then it start blinking differently. so i tried the same thing today. then i went back and Forget Paired Device, connect my Arduino to my Laptop, then reupload my code, then go to Serial.Monitor 9600 set No Ending Line -> Both NL & CR. then i reenter the AT Commands.

AT+NAME? then AT,then AT+PSWD? all worked. the AT+Name shows the name of my HC-05, and the AT+PSWD shows the password. so then i decided to finally rename my HC-05. AT+NAME=USER_FAIZ and AT+PSWD=ARDUINO individually in the Serial Monitor...and now my HC-05 has different name which is USER_FAIZ and password which is ARDUINO. i then went to my Phone, scan for bluetooth device and there it is. USER_FAIZ and password is ARDUINO.

^^what im not really sure if it is the solution im searching for. i searched some tutorials again but none of them mention of using EN Pin and most of them use STATE Pin of HC-05.So because of that, i wont "Check" this Answer as maybe this is not the best solution out. maybe just not yet. but it did solve MY problem so it may solve other users problem too so ill add it here to inform.

Ok, MAYBE I solved it^^ so the thing is, i noticed that my LED is still blinking intense instead of 2 sec light off and on. which means that i am still not in AT Mode.

but the thing is if i followed Instructables and other website tutorial. I SHOULD be able to be in AT Mode. im not exactly sure why im still not in AT Mode. So tried something:

the wiring/circuit is still THE SAME. but add something: I took another wire, connect the EN Pin of HC-05 -> 5V of Arduino. since days ago i was trying to do tinker my HC-05 here and there and i remember that i tried to put EN in 5V then it start blinking differently. so i tried the same thing today. then i went back and Forget Paired Device, connect my Arduino to my Laptop, then reupload my code, then go to Serial.Monitor 9600 set No Ending Line -> Both NL & CR. then i reenter the AT Commands.

AT+NAME? then AT,then AT+PSWD? all worked. so then i decided to finally rename my HC-05. AT+NAME=USER and AT+PSWD=ARDUINO and now my HC-05 has different name and password. i then went to my Phone, scan for bluetooth device and there it is. USER_HC05 and password is ARDUINO.

^^what im not really sure if it is the solution im searching for. i searched some tutorials again but none of them mention of using EN Pin and most of them use STATE Pin of HC-05.So because of that, i wont "Check" this Answer as maybe this is not the best solution out. maybe just not yet. but it did solve MY problem so it may solve other users problem too so ill add it here to inform.

https://i.sstatic.net/cCeV8.png

Ok, MAYBE I solved it^^ so the thing is, i noticed that my LED is still blinking intense instead of 2 sec light off and on. which means that i am still not in AT Mode.

but the thing is if i followed Instructables and other website tutorial. I SHOULD be able to be in AT Mode. im not exactly sure why im still not in AT Mode. So tried something:

the wiring/circuit is still THE SAME. but add something: I took another wire, connect the EN Pin of HC-05 -> 5V of Arduino. since days ago i was trying to do tinker my HC-05 here and there and i remember that i tried to put EN in 5V then it start blinking differently. so i tried the same thing today. then i went back and Forget Paired Device, connect my Arduino to my Laptop, then reupload my code, then go to Serial.Monitor 9600 set No Ending Line -> Both NL & CR. then i reenter the AT Commands.

AT+NAME? then AT,then AT+PSWD? all worked. the AT+Name shows the name of my HC-05, and the AT+PSWD shows the password. so then i decided to finally rename my HC-05. AT+NAME=USER and AT+PSWD=ARDUINO and now my HC-05 has different name and password. i then went to my Phone, scan for bluetooth device and there it is. USER_HC05 and password is ARDUINO.

^^what im not really sure if it is the solution im searching for. i searched some tutorials again but none of them mention of using EN Pin and most of them use STATE Pin of HC-05.So because of that, i wont "Check" this Answer as maybe this is not the best solution out. maybe just not yet. but it did solve MY problem so it may solve other users problem too so ill add it here to inform.