Skip to main content
Arduino

Return to Question

Question Protected by VE7JRO
Bumped by Community user
Bumped by Community user
Bumped by Community user
Bumped by Community user
Bumped by Community user
Removed intro
Source Link
Greenonline
Greenonline
  • 3.1k
  • 7
  • 34
  • 48

this is my first post. Sorry if formatting is not what is expected.

I am using two Arduino Unos, NRF24L01+ transceivers, and a few components as per this site on which I am following the second tutorial on this page: Arduino Wireless Communication – NRF24L01 Tutorial.

I am using the exact code from the page as well - and have set everything up as per the diagrams, however everything stops working after a short amount of time. Usually between 15 and 30 seconds, everything stays powered but it seems like the transceivers stop communicating. A reset of the Transmitting board (the one with the potentiometer) will fix the problem until it again stops 15 or 30 seconds later.

Any idea what might be going on?

this is my first post. Sorry if formatting is not what is expected.

I am using two Arduino Unos, NRF24L01+ transceivers, and a few components as per this site on which I am following the second tutorial on this page: Arduino Wireless Communication – NRF24L01 Tutorial.

I am using the exact code from the page as well - and have set everything up as per the diagrams, however everything stops working after a short amount of time. Usually between 15 and 30 seconds, everything stays powered but it seems like the transceivers stop communicating. A reset of the Transmitting board (the one with the potentiometer) will fix the problem until it again stops 15 or 30 seconds later.

Any idea what might be going on?

I am using two Arduino Unos, NRF24L01+ transceivers, and a few components as per this site on which I am following the second tutorial on this page: Arduino Wireless Communication – NRF24L01 Tutorial.

I am using the exact code from the page as well - and have set everything up as per the diagrams, however everything stops working after a short amount of time. Usually between 15 and 30 seconds, everything stays powered but it seems like the transceivers stop communicating. A reset of the Transmitting board (the one with the potentiometer) will fix the problem until it again stops 15 or 30 seconds later.

Any idea what might be going on?

Removed thanks, as per SE policy and inlined link
Source Link
Greenonline
Greenonline
  • 3.1k
  • 7
  • 34
  • 48

this is my first post. Sorry if formatting is not what is expected.

I am using two Arduino Unos, NRF24L01+ transceivers, and a few components as per this site on which I am following the 2ndsecond tutorial on this page: https://howtomechatronics.com/tutorials/arduino/arduino-wireless-communication-nrf24l01-tutorial/Arduino Wireless Communication – NRF24L01 Tutorial.

I am using the exact code from the page as well - and have set everything up as per the diagrams, however everything stops working after a short amount of time. Usually between 15 and 30 seconds, everything stays powered but it seems like the transceivers stop communicating. A reset of the TRANSMITTINGTransmitting board (the one with the potpotentiometer) will fix the problem until it again stops 15 or 30 seconds later.

Any idea what might be going on? Thanks much!

this is my first post. Sorry if formatting is not what is expected.

I am using two Arduino Unos, NRF24L01+ transceivers, and a few components as per this site on which I am following the 2nd tutorial on this page: https://howtomechatronics.com/tutorials/arduino/arduino-wireless-communication-nrf24l01-tutorial/

I am using the exact code from the page as well - and have set everything up as per the diagrams, however everything stops working after a short amount of time. Usually between 15 and 30 seconds, everything stays powered but it seems like the transceivers stop communicating. A reset of the TRANSMITTING board (the one with the pot) will fix the problem until it again stops 15 or 30 seconds later.

Any idea what might be going on? Thanks much!

this is my first post. Sorry if formatting is not what is expected.

I am using two Arduino Unos, NRF24L01+ transceivers, and a few components as per this site on which I am following the second tutorial on this page: Arduino Wireless Communication – NRF24L01 Tutorial.

I am using the exact code from the page as well - and have set everything up as per the diagrams, however everything stops working after a short amount of time. Usually between 15 and 30 seconds, everything stays powered but it seems like the transceivers stop communicating. A reset of the Transmitting board (the one with the potentiometer) will fix the problem until it again stops 15 or 30 seconds later.

Any idea what might be going on?

Source Link
shanearthur
shanearthur
  • 9
  • 2

Arduino and RF24 library: communication stops after short amount of time

this is my first post. Sorry if formatting is not what is expected.

I am using two Arduino Unos, NRF24L01+ transceivers, and a few components as per this site on which I am following the 2nd tutorial on this page: https://howtomechatronics.com/tutorials/arduino/arduino-wireless-communication-nrf24l01-tutorial/

I am using the exact code from the page as well - and have set everything up as per the diagrams, however everything stops working after a short amount of time. Usually between 15 and 30 seconds, everything stays powered but it seems like the transceivers stop communicating. A reset of the TRANSMITTING board (the one with the pot) will fix the problem until it again stops 15 or 30 seconds later.

Any idea what might be going on? Thanks much!